Search found 128 matches
- Fri Aug 06, 2010 5:10 pm
- Forum: Performance Technical
- Topic: Why Disable OKO 24 Power Jet?
- Replies: 83
- Views: 20470
Re: Why Disable OKO 24 Power Jet?
OK, I'm still having a problem here with this supposed leaning out in the mid-range stuff. Basically HOW? If this power jet works just like the Dial-a-jet, once it comes on line and starts flowing fuel, it stays on line until the air flow thru the carb drops below the level required to pull fuel th...
- Fri Aug 06, 2010 11:58 am
- Forum: Performance Technical
- Topic: Why Disable OKO 24 Power Jet?
- Replies: 83
- Views: 20470
Re: Why Disable OKO 24 Power Jet?
The power jet on my OKO works just like a dial-a-jet. Vacuum from ahead of the trottle plate pulls in fuel via the power jet directly from the fuel bowl. I dont see how this would lean out the mid-range in any way.
-Nathan
-Nathan
- Fri Aug 06, 2010 10:23 am
- Forum: Performance Technical
- Topic: Why Disable OKO 24 Power Jet?
- Replies: 83
- Views: 20470
Re: Why Disable OKO 24 Power Jet?
Wheelman,
I have a OKO 24 with power jet you can borrow to see if you can get your bike tuned well with it- just let me know and I'll send it out.
Nathan
Rio Rancho NM
I have a OKO 24 with power jet you can borrow to see if you can get your bike tuned well with it- just let me know and I'll send it out.
Nathan
Rio Rancho NM
- Tue Jul 27, 2010 4:26 pm
- Forum: General Chit-Chat
- Topic: Lowering My Standards
- Replies: 8
- Views: 2840
Re: Lowering My Standards
What type of transmission does that thing have? (looks like centrifugal clutch but?)
Later,
Nathan
Later,
Nathan
- Tue Jul 27, 2010 12:37 am
- Forum: Technical Help
- Topic: CH150 valve timing help
- Replies: 5
- Views: 5408
Re: CH150 valve timing help
I admit, I don't own a 150. I've rebuilt one for a friend and it did alright. The setup is similar to a CH80, though. I set mine up by Honda-san's procedure for cam timing, but I did run the exhaust valve at 0.6mm instead of 0.5mm (bit too tappy at 0.7mm) to keep the valve from tightening up too mu...
- Mon Jul 26, 2010 10:46 pm
- Forum: Technical Help
- Topic: CH150 valve timing help
- Replies: 5
- Views: 5408
Re: CH150 valve timing help
I'd look here first: http://www.hondaspree.net/other/Elite_CH150-H_Service_Manual_85-86.pdf Section 6, page 14. Sets up similarly to a CH80 Elite. There's a mark on the flywheel and on the cam. Once those are set, install the cam chain tensioner and set the valve lash. Won't work. Trust me been the...
- Mon Jul 26, 2010 9:20 pm
- Forum: Technical Help
- Topic: CH150 valve timing help
- Replies: 5
- Views: 5408
Re: CH150 valve timing help
I do it by feel with the engine running- Get it started and loosen one adjuster and simply move the adjuster until the valve stops ticking (use a tiny bit of pressure) and tighten up the adjuster. Then do the opposite valve. I wouldn't worry about what each graduation is. See: HTTP://www.ch250.net/t...
- Thu Apr 01, 2010 7:34 am
- Forum: General Discussion
- Topic: PG Pipes Get Louder?
- Replies: 31
- Views: 14568
Re: PG Pipes Get Louder?
Guys, There is a single layer of packing in the PG Long- I cut my used one open to see if it would be feasible to modify it to help knock some of the sound volume down. Right near the very back of the pipe there is an inner perforated core and a single layer of fiberglass packing (about 1/8" th...
- Tue Feb 09, 2010 11:10 am
- Forum: Performance Technical
- Topic: Mikuni Cable hook up
- Replies: 3
- Views: 1278
Re: Mikuni Spiders
Greetings; There should be a little white plastic "spider" that came with the carb. Once the cable end ("aglet") engages the keyhole, the spider slides over it and one "Leg" keeps the cable from sliding over to the wide part of the keyhole. I saw a Mikuni diagram somew...
- Mon Feb 08, 2010 10:54 pm
- Forum: Performance Technical
- Topic: Mikuni Cable hook up
- Replies: 3
- Views: 1278
Mikuni Cable hook up
Please help, Maybe I'm a little retarded but I bought a flatslide cable to hook up my mikuni and I honestly can't figure out how to connected the cable- it has a small ball and an elongated slot that the ball fits through but it keeps comming out. I'm I missing something? Is there a diagram somewher...
- Wed Feb 03, 2010 5:46 pm
- Forum: Performance Technical
- Topic: Any Experience w/Watercooled Setups
- Replies: 4
- Views: 2165
Re: Any Experience w/Watercooled Setups
Awesome,
Thanks for the answers. First hand experience is always best.
-Nathan
Thanks for the answers. First hand experience is always best.
-Nathan
- Wed Feb 03, 2010 9:52 am
- Forum: Performance Technical
- Topic: Any Experience w/Watercooled Setups
- Replies: 4
- Views: 2165
Any Experience w/Watercooled Setups
This is primarily directed at Bakaracer as I know he is currently running a watercooled setup but I am looking for any experiences with the WC setups Ebay currently has WC kits for sale that look pretty interesting. How do they run? What are the advantages? Are the temps more stable? Do you have to ...
- Fri Jan 29, 2010 11:47 pm
- Forum: General Discussion
- Topic: 1994 Elite $300
- Replies: 5
- Views: 2035
Re: 1994 Elite $300
Whoops- my bad. I thought the af16's started in 94.
- Fri Jan 29, 2010 7:58 pm
- Forum: General Discussion
- Topic: 2001 Elite $500 Daytona Fl
- Replies: 1
- Views: 976
- Fri Jan 29, 2010 7:56 pm
- Forum: General Discussion
- Topic: 94 Elite- Tampa $400
- Replies: 5
- Views: 1882