Honda Spree and Elite 50 Forums

bakaracer wrote:Did you put some 2 stroke oil on the piston,rings,and cylinder wall before you installed it?

yes i just dipped my finger in the bottle then smeared it all around.. What will that matter for compression?

How do you crank a bolt or nut to any number PSI??? Maybe foot/pounds or Newton Meters or Kilograms/Meters But never PSI. PSI is what compression is read in. I would suspect that head and or the jug are not flat. there you go bear all fixed up for ya, i was typing that in a hurry with a screaming 6...

I recently installed a 50mm bbk, just got the motor back together today. so i did a compression test. i had the head torqued down to 9ft/lbs, i used a cordless drill to crank the motor. my reading was 122psi, so i wanted to just snug the head bolts (for good luck) to atleast 10ft/lbs. so i did, re-r...

awesome thanks thats a good positive answer!!! i just wanted to make sure i had it correct, thats what it sounded like everyone was saying but just wanted to double check!!!

ok the spring ring goes in the lower or second groove. got that!!!! the lettering goes up, but i looked at both the rings i dont see a taper on the rings or the piston. So im still not sure what ring goes where. I dont mean to keep asking but i dont want to screw this up. ive takin the time to cut t...

The hexagonal ring goes under the 2nd ring from the top of the piston. Check the widths of the rings; sometimes the rings are different thicknesses which can tell u which is top and which is bottom. Hope this helps. J i checked the sizes and the 2 rings have a 1mm thickness and the hexagonal 1 is a...

i have a 50mm bbk from jiangwayne. Im not sure what kind it is, but im guessing its a Ruima, because the bag the rings came in says Ruima on it other than that there is no markings of brand or manufacturer on it. The bag came with 3 rings. Im just not sure what the 3rd ring is, if its a oil ring or ...

So i will try going to 112 with one and try another stepping up to 125, in the area that veedubh20 says they sell. Just for clarification, Daytona is a tuning company that sells a jet kit. Not sure if you were going to scour Daytona Beach for moped parts ;) As far as CHT gauges go, everyone I know ...

Greetings: DayWOT on eBay and others (JiangWayne.com, methinks...) sell a Daytona jet kit that has machined jets in sizes up to 105. If you purchase a set of indexing bits from Harbor Freight and a digital caliper, you can enlarge your current stock jets to whatever size you wish - the number refer...

With your 100 main how does the plug look? You know how to do plug checks? Its breaking in anyways, so your main jet mainly controls your top speed which you should not be testing out until after break in. Save your money and get a carb that has more adjustments, like pilot jet, different needle ch...

I recently order some more parts for my 2001 elite 50, new exhaust and a bolt on 50mm bbk. My question is the stock carb. Can i jet the stock carb big enough for now till im able to get a new carb? How big can you jet the stock carb? Im already at 100 with a no restriction airfilter. And last of all...

yup gonna swap them gears back to stock, until i get the bbk. but not much of a increase with the rest of the setup up. any ideas why?

measured the belt at 14.5mm its right there, will that make that big of difference?

:newb: I have a 2001 elite 50s i derestricted, added a no restriction air filter and jetted to 100, and was running great approx 39mph. Then i ordered some mods. I put on a oko variator kit 2k clutch springs, 1k center spring and went up to 66g roller weights. I got up to about 41 mph. Then i tryed ...