Search found 132 matches
- Sat May 21, 2011 10:44 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: Edited: New thread but someone please help! 85 spree
What does your spark plug look like after a few attempted starts? If you spark plug gets too saturated with gas and oil, then it will begin to find a different path of least resistance to displace it's charge, instead of arcing across to the proper point. This could cause serious problems with tryi...
- Sat May 21, 2011 5:50 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: Edited: New thread but someone please help! 85 spree
low compression means time for a ring job right?..
- Sat May 21, 2011 3:12 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: Edited: New thread but someone please help! 85 spree
when i pull both lines off (leaving both ends attached to petcock) and suck on vaccum line fuel comes from the other..
- Sat May 21, 2011 2:17 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: Edited: New thread but someone please help! 85 spree
ok i got a little confused reading the tech docs. but wouldnt the scooter not start if the flywheel timing was off?
- Sat May 21, 2011 2:08 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: sorry to make a new thread but someone please help!!@!
i agree with bear. if it starts up but dies, your bike obviously isn't idling. turn the screw in a bit. also... you may be getting too much or too little air; or too much fuel. i got my gf's spree running for a second, then it stopped...seems its back to its old tricks of fuel flowing through the v...
- Sat May 21, 2011 2:06 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: sorry to make a new thread but someone please help!!@!
ok. flywheel is controlled by cdi correct?Wheelman-111 wrote:Greetings:
Consider the possibility that it isn't the carb. At all. Compression? Spark plug? Flywheel timing? Reed valves? Crank Seals? Vacuum leak? All the carb-cleaning and screw-spinning in the world won't fix those.
- Sat May 21, 2011 1:52 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: sorry to make a new thread but someone please help!!@!
Do you have a petcock on this scoot? What condition is your autobystarter in? Have you taken a look at the spark plug between these bogging sessions? Have you taken a close look at the actual float to make sure it isn't hanging up anywhere, or maybe cracked? Between all these cleaning sessions have...
- Fri May 20, 2011 3:38 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: sorry to make a new thread but someone please help!!@!
ive moved both screws countless timez.. should i bend the float so that more gass flows in? You can NOT just twist things, you have to know what you are doing, which you obviously don't have a clue. Go back to the factory recommended settings and then turn the idle speed screw in 1 turn. http://i14...
- Fri May 20, 2011 1:47 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Re: sorry to make a new thread but someone please help!!@!
ive moved both screws countless timez.. should i bend the float so that more gass flows in?
- Fri May 20, 2011 12:57 pm
- Forum: Technical Help
- Topic: Edited: New thread but someone please help! 85 spree
- Replies: 60
- Views: 13865
Edited: New thread but someone please help! 85 spree
ok i have cleaned every single part of my carb like a champ.. no spot was untouched.. i got new needle valve put it in and it STILL wont run.. its turning on and bogging extremely low then just dies out.. if i touch the throttle it dies even faster. the throttle stop screw has to be almost all the w...
- Thu May 19, 2011 11:19 pm
- Forum: Technical Help
- Topic: SOMEONE PLEASE HELP ME!!
- Replies: 51
- Views: 11595
Re: SOMEONE PLEASE HELP ME!!
unfortunately the closest dealer is 2 hours away if your doing 70mph.... and the scooter doesnt run sooo.. lol. it was too late after i cleaned the carb so i havent got to put it back on and check yet
- Thu May 19, 2011 6:27 pm
- Forum: Technical Help
- Topic: is there anyother carb that fits the spree?
- Replies: 4
- Views: 1305
Re: is there anyother carb that fits the spree?
sb50?... thats off aN elite correct?
- Thu May 19, 2011 6:26 pm
- Forum: Technical Help
- Topic: SOMEONE PLEASE HELP ME!!
- Replies: 51
- Views: 11595
Re: SOMEONE PLEASE HELP ME!!
i ordered from cheapcycleparts.comgot the product today. but it was 10$ shipping on a 16$ part smaller than my pinky nail... frigger rip off.. anyways bout to go see if it works.
- Wed May 18, 2011 5:02 pm
- Forum: Technical Help
- Topic: Carb troubles...
- Replies: 4
- Views: 1843
Re: Carb troubles...
thats where the fuel leakes when you drain your bowl.. ha.
- Wed May 18, 2011 11:25 am
- Forum: Technical Help
- Topic: still wont run.
- Replies: 37
- Views: 9975
Re: still wont run.
do i wss looking at the wiki and it says grinding your gears makes the spree much faster.... worth the effort?:::