The VW gasket is where it's at perfect fit and seal.
Search found 512 matches
- Mon Aug 24, 2015 9:57 am
- Forum: Performance Technical
- Topic: What exhaust gasket works best?
- Replies: 6
- Views: 5330
- Wed Aug 19, 2015 10:48 am
- Forum: General Discussion
- Topic: Attn all Oahu moped riders
- Replies: 9
- Views: 4954
Re: Attn all Oahu moped riders
Yeah that sucks. $15 bucks every 3 years here in Michigan, no insurance or anything, and 100cc or less. Cops really don't pay any attention to you as long as you aren't going over the posted speed limits.
- Sun Aug 16, 2015 9:58 am
- Forum: Technical Help
- Topic: upgraded gears in the AF16E motor
- Replies: 38
- Views: 17756
Re: upgraded gears in the AF16E motor
I had a set do this as well exact same spot, I put a shim on the axle that sat inside the seal right on the bearing and problem solved. It was the Tida straight cut gears, the gear is about 1mm thicker then stock and my other set of 8.44s that I have. What gears do you have there?
- Thu Aug 13, 2015 12:11 am
- Forum: Builder's workshop
- Topic: 01 Honda Elite- ZX headset swap, disk brake, DIO FUN
- Replies: 125
- Views: 69109
Re: Too many build threads- 01 Honda Elite
^ Shut Up Troll. Every post you make is stupid nonsense rambling we don't need that crap here.
- Wed Aug 12, 2015 9:16 am
- Forum: Builder's workshop
- Topic: Summer Build: '96 SA50
- Replies: 30
- Views: 22006
Re: Summer Build: '96 SA50
9g rollers are to heavy even when mixed. And you always want to mix evenly when mixing rollers 3 and 3. Throw all 6s in and she will be hitting 8.5-9k and be a beast.
- Sat Aug 01, 2015 6:00 pm
- Forum: Technical Help
- Topic: Any possibility of "bad" carb causing overheating?
- Replies: 77
- Views: 24871
Re: Any possibility of "bad" carb causing overheating?
Ok so how hot has it actually gotten and how long at WOT did it take to get there? How is the bike running in general?
- Thu Jul 30, 2015 1:27 pm
- Forum: General Discussion
- Topic: Will Chinese disk brakes fit Elite?
- Replies: 13
- Views: 6814
Re: Will Chinese disk brakes fit Elite?
I also mated up a Chinese disc from end. Just modded my fork tube slightly and used the bearing race off of the Chinese scoot. Works perfect!
- Thu Jul 30, 2015 10:13 am
- Forum: General Discussion
- Topic: Malossi Big Bore kit for a nb50 needed!!
- Replies: 16
- Views: 11253
Re: Malossi Big Bore kit for a nb50 needed!!
Yes go with the malossi, and you will be able to get jets from honda. Or just a lot so you have lots. I would just run it with the stock pipe and carb at first to brake it in then start looking into those. Graphite is gonna have some sweet pipes coming soon I think :) Hey Brandon can you get the mal...
- Wed Jul 29, 2015 9:32 am
- Forum: Scooter Showcase
- Topic: TinyElvis Unsullied Scooter!
- Replies: 55
- Views: 34114
Re: TinyElvis Unsullied Scooter!
You have to use tubes on the stock rims.
- Sun Jul 26, 2015 9:23 am
- Forum: Builder's workshop
- Topic: Wheel options for a 96' Elite SR?
- Replies: 24
- Views: 18626
Re: Wheel options for a 96' Elite SR?
Yeah that will rub under load for sure. If you take the rim off and put a thick washer on the axel then the rim you can get a little more clearance.
- Sat Jul 25, 2015 8:43 pm
- Forum: Scooter Showcase
- Topic: New Spree Build..AKA.."Little Evil"..125cc Hard Tail...
- Replies: 94
- Views: 61232
Re: New Spree Build..AKA.."Little Evil"..125cc Hard Tail...
She sounds sweet man! And looks great too!
- Fri Jul 24, 2015 7:26 pm
- Forum: General Discussion
- Topic: Engine number and titling issue
- Replies: 6
- Views: 6310
Re: Engine number and titling issue
Run up to Michigan they will register it for you.
- Fri Jul 24, 2015 5:11 pm
- Forum: Performance Technical
- Topic: stage 6 manifold
- Replies: 7
- Views: 5656
Re: stage 6 manifold
My PHBL25 was really close with the malossi mani but clears by far with the ct black.
- Fri Jul 24, 2015 9:56 am
- Forum: Performance Technical
- Topic: Need advice for my 84 Aero 50
- Replies: 7
- Views: 5038
Re: Need advice for my 84 Aero 50
Your only option would be to swap motors as they didn't make any bbks or any aftermarket parts for your motor. An af16 swap will be pretty much plug and play other then you may have to move the shock mount back a little bit and might have to do a little motor mount work. And if you've been reading y...
- Thu Jul 23, 2015 11:15 pm
- Forum: Scooter Showcase
- Topic: New Spree Build..AKA.."Little Evil"..125cc Hard Tail...
- Replies: 94
- Views: 61232
Re: New Spree Build..AKA.."Little Evil"..125cc Hard Tail...
What front fender do you have there? Looking for one my self.