Search found 49 matches
- Tue Aug 14, 2012 10:51 pm
- Forum: General Clubs Section
- Topic: who lives in michigan
- Replies: 76
- Views: 93252
Re: who lives in michigan
ann arbor
- Sat Aug 04, 2012 10:54 pm
- Forum: General Discussion
- Topic: copper coat paint update
- Replies: 15
- Views: 6526
Re: copper coat paint update
lets see the pics
- Sat Aug 04, 2012 10:48 pm
- Forum: Scooter Showcase
- Topic: 85 Aero restoration (slowly but surely)
- Replies: 5
- Views: 4571
- Sat Aug 04, 2012 10:41 pm
- Forum: General Chit-Chat
- Topic: Smack talkers and trolls.
- Replies: 16
- Views: 8846
- Sat Aug 04, 2012 10:37 pm
- Forum: Scooter Showcase
- Topic: honda spree si
- Replies: 18
- Views: 12280
Re: honda spree si
holy cow does the motor hit the ground when u turn?
- Wed Jun 20, 2012 6:57 pm
- Forum: Performance Technical
- Topic: spree pulley mod good or bad
- Replies: 3
- Views: 3027
Re: spree pulley mod good or bad
i did it quite afew years ago. I ended up using some washers to (finely tune it) adjust the spacing. But it is a mod def. worth doing to the spree.
- Tue Jun 19, 2012 1:04 am
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
Re: 99 sa50
i would not run without the holes.. i put my stock motor back in
- Sat Jun 16, 2012 11:16 am
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
Re: 99 sa50
well i have not blown it up yet! I was kinda hopeing to hear some more feedback on my carburator setup i put a piece of tape over one of the three holes. I guess it works fine i dont think it is running hot or has gotten hot. but i have put about a hundred easy miles on the bore. but i need to do so...
- Wed Jun 13, 2012 9:56 am
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
Re: 99 sa50
I ended up putting the stock air box on and drilled three eighth inch holes in it. If I cover one hole with the finger it will four stroke during the midrange my idle is set a lil high and the mixture screw is set in between one and one and a half out. it seems to be running ok I really wish I had a...
- Mon Jun 11, 2012 1:48 pm
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
Re: 99 sa50
Thanks for all the replys everyone I did install the corsa I'm running a 98 jet stock carb. I have not ran it much though and do understand the pilot is small it worries me. I was going to buy some bigger jets. Should I Just install the 28mm 130 main with about a 50 pilot.? I try to keep it out of t...
- Fri Jun 01, 2012 11:20 am
- Forum: General Discussion
- Topic: can u still buy a pg long?
- Replies: 5
- Views: 4381
Re: can u still buy a pg long?
Thanks for the reply! Is there an exhaust you would recommend? I am looking for most acceleration.
- Thu May 31, 2012 11:13 pm
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
Re: 99 sa50
what size jets should i start with?
uni filter installed.
uni filter installed.
- Thu May 31, 2012 1:34 pm
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
- Wed May 30, 2012 3:09 pm
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
Re: 99 sa50
my bad
- Wed May 30, 2012 2:29 pm
- Forum: Performance Technical
- Topic: 99 sa50
- Replies: 18
- Views: 4731
99 sa50
hello, i have a corsa bore i am thinking about installing in my 99. i have 9:1 gears, high speed vari, sef ramp plate, assorted weights, aftermarket (i dont kno what it is called) i think it is a 1000 rpm clutch spring that adjust the width or the rear pully. i also have a 28 mm carb with intake. i ...