Search found 10 matches
- Mon Feb 27, 2017 2:01 am
- Forum: Builder's workshop
- Topic: Honda Spree Build
- Replies: 8
- Views: 7152
Re: Honda Spree Build
So after gatgering parts and installing this winter, i cant get it to start. I added the polini carb kit from scooter swap shop (21mm) and the upgraded intake from webikejapan along with the peoples pipe. Any ideas of why it wont start? Has compression, has gas, has spark... what did i do wrong???
- Sun Jan 01, 2017 7:10 pm
- Forum: Technical Help
- Topic: Alternative tire size?
- Replies: 1
- Views: 2337
Alternative tire size?
Running stock nq50 rims with 2.50-10 size tire. Will a 3.50-10 tire fit? I have no clue how tire sizes work .-.
http://www.treatland.tv/sava-MC18-scoot ... 0-tire.htm ?????
http://www.treatland.tv/sava-MC18-scoot ... 0-tire.htm ?????
- Fri Dec 23, 2016 12:04 am
- Forum: General Discussion
- Topic: Getting the Tazland BBK, GEARS, + MLM ran on a dyno
- Replies: 360
- Views: 174709
Re: Getting the Tazland BBK, GEARS, + MLM ran on a dyno
Does the throttle cable in the Kitaco work with stock spree throttle tube or do you have to purchase another?
- Sun Dec 18, 2016 1:16 am
- Forum: Builder's workshop
- Topic: Honda Spree Build
- Replies: 8
- Views: 7152
Honda Spree Build
I have an '87 Honda spree.Recently added a 75cc big bore kit from chop shop to it. New rear suspension, cdi, coil, and gearing (also from chopshop). Looking to get a new Carb for the new 75cc bore. Not sure what carb size or anything.If you could help me out on how you think I should set this up, th...
- Thu Sep 15, 2016 11:53 pm
- Forum: Builder's workshop
- Topic: More engine problems
- Replies: 7
- Views: 6706
More engine problems
1986 Honda Spree NQ50 -Installed 75cc big bore with jet and upgraded gearing kit sold by chopshop on ebay -UNI air filter -Racing CDI -OML ignition coil ...basically alot of ebay add ons still only getting up to 35-40mph flat. Recently it has been having a harddddd time starting but starts easier wi...
- Fri Apr 22, 2016 2:23 pm
- Forum: Technical Help
- Topic: Installing Big Bore
- Replies: 4
- Views: 3605
Re: Installing Big Bore
Would I have to scrap the oil injector? A friend reccomended just adding a cap full of twostroke oil when i fill up
- Wed Apr 20, 2016 8:08 pm
- Forum: Technical Help
- Topic: Installing Big Bore
- Replies: 4
- Views: 3605
Installing Big Bore
I recently installed a 75cc big bore kit on my '87 Honda Spree. The kit came with everything to install and a upgraded jet. It runs and everything but still tops out at 30ish. A friend recommended I check the oil injector... any ideas?
- Sun Nov 08, 2015 11:51 pm
- Forum: Technical Help
- Topic: Derestrict?
- Replies: 3
- Views: 3342
Derestrict?
I recently upgraded my 86 spree to a 75cc big bore kit. I adjusted the mixture, even added octane. It came with a bigger jet and i did that too but it still only tops out at around 30mph... What am i doing wrong?
- Mon Oct 05, 2015 6:15 pm
- Forum: Technical Help
- Topic: Engine Bogging
- Replies: 5
- Views: 2810
Re: Engine Bogging
Thanks. I ended up checking the gaskets as you said. Upon further inspection, i saw that there was a leak in the cylinder. We put the gasket on wrong so gas was not getting into the cylinder.thanks for your help
- Mon Oct 05, 2015 12:59 am
- Forum: Technical Help
- Topic: Engine Bogging
- Replies: 5
- Views: 2810
Engine Bogging
I have a 1986 honda spree nq50. It sat for 25years till last summer when i inherited it and got it running. I rode it as a daily driver to save on gas. Recently, ive been upgrading her. I got an upgraded spark plug, spark pug wire, and proformance cdi. Today i installed a 74cc big bore kit. It came ...