Honda Spree and Elite 50 Forums

bonesv wrote:So you have a Kymco zx.

Yeah.

I have a 2001 Zx50 that I finished this spring and I have some questions regarding interchangability of gears. I am a trooper when it comes to tirelessly searching for answers, I have yet to see a difinitive answer on remedying the lack of gear choices for the zx50 and I was hoping someone somewhere...

definitely, you want to be 4-5G on the rollers. Also check quish, to be safe. If your too tight you'll burn a hole in your piston. yeah that would suck. My next question to you is I went from 6.0g sliders to 5.5 sliders and it would hit the over revv at around 55-60mph so I went back to 6g and it w...

Hi mt. I'm not an expert ,but what I would do. Sounds like you need to go down to 5g or lower on your variator, 1000- 1500 on rear clutch and center spring. Check your compression. around 135 is good. High compression May also give you a pinging noise. GL. Thanks, yeah my compression was just at 15...

Ok ive posted before about slow takeoff speeds but I thought I would try to get more into the cvt aspect of it then possible mechanical issues as Ive tirelessly test and checked everything, compression test, leakdown test, apart then together. The issue is that I see and or read of everyone elses af...

Took the PG long pipe off my Zx50 after G9 talked me into the Corsa Race pipe. The Corsa pipe is an animal, however I am not a veteran, actually pretty new to it so I have not tested anything but the two pipes listed. I did however come from the 2, stroke atv dirkbike world so I know a good power cu...

pg is dead after 9200rpm. There is no reason you shouldn't be spinning 11,500-12k. There will be guys saying they do 80mph on a stock corsa with pg. Sure, maybe if you were to go down a cliff, or down a mountain pass tucked with gravity and a tailwind. Look how hard it falls apart. This is on a cor...

I have 2 elites, one with the c16 and other with the arrow. Both pull really hard. Ive also heard the polini pipe in action on g9's bike in person. Its sounds animal! I had really stiff clutch springs maxed and realized i was just wasting alot of low rpms cuz the beginning of my band was right arou...

check compression and squish, report back with the numbers. we have seen some oddball deck height differences in these honda blocks. Your comp is either too high, or you have an air leak. Your super fat jetting suggests an air leak. I run the same setup at sea level and its a 108 main on the same c...

hi, I have a zx50 that I had been doing the finishing touches on tuning then added the Corsa pipe and it is dangerously hot all of a sudden, creeps around 330-350 on my vapor but when I hit cruising speeds of 40mph or more it sits on 400 degrees sometimes a little more. I can leave my house and driv...

Change spring +1. Roller weights - add +1. Drop pilot jet +1. Sorry, I didnt understand your or the lingo on this one. are you talking Percent? I am 130lbs which may or may not change your answer. I was 171 and lifting weights in november and got sick so im down to 130 now..yikes. Also I went from ...

I have 2 elites, one with the c16 and other with the arrow. Both pull really hard. Ive also heard the polini pipe in action on g9's bike in person. Its sounds animal! I had really stiff clutch springs maxed and realized i was just wasting alot of low rpms cuz the beginning of my band was right arou...

Change spring +1. Roller weights - add +1. Drop pilot jet +1. Sorry, I didnt understand your or the lingo on this one. are you talking Percent? I am 130lbs which may or may not change your answer. I was 171 and lifting weights in november and got sick so im down to 130 now..yikes. Also I went from ...

screw 3 turns out, may be too much. 2 1/2 max I think? also, needle on third clip? from the top? what type of carb? PG long will not REV high as C16, Arrow. or polini. Talk to graphit9. he know's how high it will Rev. he tested on a dyno. GL. Yeah 3rd from top, it was on the 4th because it would &q...

I have 2 elites, one with the c16 and other with the arrow. Both pull really hard. Ive also heard the polini pipe in action on g9's bike in person. Its sounds animal! I had really stiff clutch springs maxed and realized i was just wasting alot of low rpms cuz the beginning of my band was right arou...