Search found 77 matches
- Sun Jun 11, 2023 6:21 am
- Forum: Performance Technical
- Topic: 1987 se50 elite mlm pipe.
- Replies: 3
- Views: 3680
Re: 1987 se50 elite mlm pipe.
I will get a scale eventually . I tossed in three 6s and three 8s to get seven and still bogs. Maybe smaller needed
- Sat Jun 10, 2023 10:46 pm
- Forum: Performance Technical
- Topic: 1987 se50 elite mlm pipe.
- Replies: 3
- Views: 3680
1987 se50 elite mlm pipe.
Hey guys
I put on the mlm pipe as well as 1500rpn springs and contra. Also up jet to an 86(might up again to 88)…I don’t have a scale so wondering what stock weight is for rollers so I know where to start with variator tuning. Or what size gram anyone suggests.? Thanks
I put on the mlm pipe as well as 1500rpn springs and contra. Also up jet to an 86(might up again to 88)…I don’t have a scale so wondering what stock weight is for rollers so I know where to start with variator tuning. Or what size gram anyone suggests.? Thanks
- Fri Apr 29, 2022 8:49 pm
- Forum: Technical Help
- Topic: Help with '87 Spree :-(
- Replies: 7
- Views: 1732
Re: Help with '87 Spree :-(
Mine works fine on cars but I tried it on couple sprees and scooters never climbs beyond 80psi.. junk
- Thu Apr 28, 2022 9:34 pm
- Forum: Technical Help
- Topic: Help with '87 Spree :-(
- Replies: 7
- Views: 1732
Re: Help with '87 Spree :-(
Hey.. did you try drilling a hole in the gas cap to help it vent.. and FYI. My harbor freight compression tester never went above 80 on my spree. Tried a snap on and it was perfect.
- Fri Apr 15, 2022 2:26 pm
- Forum: Technical Help
- Topic: 86 spree kickstart stuck
- Replies: 11
- Views: 3347
Re: 86 spree kickstart stuck
Thanks.. Unrelated to kick start cover .but as soon as I engage electric start it gets jammed aswell… starter works . Bendix was cleaned and is working correctly . The drive face is good and straight.
- Thu Apr 14, 2022 9:17 am
- Forum: Technical Help
- Topic: 86 spree kickstart stuck
- Replies: 11
- Views: 3347
Re: 86 spree kickstart stuck
Where do I found the clutch cover gasket. Any ideas ?
- Thu Apr 14, 2022 6:26 am
- Forum: Technical Help
- Topic: 86 spree kickstart stuck
- Replies: 11
- Views: 3347
Re: 86 spree kickstart stuck
Thanks for advice. Strange my other spree is fine without the case gasket.. strange world . Cheers
- Mon Apr 04, 2022 6:17 am
- Forum: Technical Help
- Topic: 86 spree kickstart stuck
- Replies: 11
- Views: 3347
Re: 86 spree kickstart stuck
Hey. I replaced the thrust washer and the snap ring . Still same as before.. and I try electric start with the same problem. So that would rule out bad kicker.. the crank is straight and the drive face teeth for the electric and kickstart are not worn. I’m clueless at this point
- Wed Mar 23, 2022 6:22 am
- Forum: Technical Help
- Topic: 86 spree kickstart stuck
- Replies: 11
- Views: 3347
Re: 86 spree kickstart stuck
Greetings. I’ve tried to mimic that thrust washer but there not enough space after to get the face over the splines on the crank..I actually just found the thrust washer available from Honda still. Maybe I’ll grab one.that snap ring and the grove your referring to is slightly worn. Maybe I’ll try to...
- Sat Mar 19, 2022 8:34 pm
- Forum: Technical Help
- Topic: Spree aftermarket led blinker
- Replies: 15
- Views: 4119
Re: Spree aftermarket led blinker
They are 8ohm 25 watt. Of eBay.
- Sat Mar 19, 2022 7:42 pm
- Forum: Technical Help
- Topic: 86 spree kickstart stuck
- Replies: 11
- Views: 3347
86 spree kickstart stuck
Hey guys. 86 spree for my son. Get five kicks on the kick starter and it gets stuck. The lever does return then just gets stuck. It feels like the gear spins in to drive the face but dosent return. I’ve dismantled the entire thing cleaned everything relubed everything all the teeth on the gear seem ...
- Fri Mar 18, 2022 11:12 am
- Forum: Technical Help
- Topic: Electronic 2 Pin LED Flasher Test
- Replies: 20
- Views: 5730
Re: Electronic 2 Pin LED Flasher Test
I finally got LED blinkers working on the rear of the old spree . My question is how hot do they resistors get.? I got the tiny aluminum fin ones that i screwed underneath the frame away from anything. When I do the front I wanna know how to safely place the resistors … thanks
- Wed Dec 22, 2021 9:25 pm
- Forum: Technical Help
- Topic: 1985 honda spree starter.
- Replies: 3
- Views: 1335
Re: 1985 honda spree starter.
Iv sent them in before to be relined and they came out good.. I also just scored a clutch and bell on eBay for 10$shipped. Score
- Thu Nov 04, 2021 12:28 pm
- Forum: Technical Help
- Topic: 85' Spree fires up then dies
- Replies: 16
- Views: 4684
Re: 85' Spree fires up then dies
In my experience I always drill a hole in the gas cap to help the air vent on this old scoots. Just don’t fill up to the top and wheelie around.
- Thu Nov 04, 2021 12:23 pm
- Forum: Technical Help
- Topic: Spree carb is junk?
- Replies: 22
- Views: 4797
Re: Spree carb is junk?
Thanks. I’ve Ben working on it for a friend now I can get finally get it back to him and get on my own projects again