Search found 70 matches
- Tue May 31, 2011 2:06 pm
- Forum: Technical Help
- Topic: Idling issues with a 88' Honda Elite E! Help ASAP!
- Replies: 24
- Views: 10006
Re: Idling issues with a 88' Honda Elite E! Help ASAP!
My 1985 Spree will sometimes do just as you are describing and it is adjusted fine. A few things that can help with these finicky carbs... Do a complete carb cleaning once a year preferably using an ultrasonic cleaner. At the very least, make sure the main jet is completely clear. I use an old proje...
- Tue May 11, 2010 9:18 am
- Forum: General Discussion
- Topic: Coating the gas tank
- Replies: 6
- Views: 2835
Re: Coating the gas tank
Here is what I found... First, the filter tube is installed from the outside. There is a thin lip around the bottom that keeps it from going in any further than flush with the bottom of the threaded drain. This same diameter filter tube is used on many Honda bikes of this era. The main difference be...
- Wed May 05, 2010 1:58 pm
- Forum: General Discussion
- Topic: Coating the gas tank
- Replies: 6
- Views: 2835
Coating the gas tank
I have my gas tank soaking in CLR as I type this and I plan to coat the cleaned take with Master Series Silver Rust Sealer in a day or so. Question... Is there an easy way to remove the plastic screen/filter tube? I believe it is inserted from the outside. Is is just pressed in or threaded in? Thanks!
- Mon Jun 01, 2009 5:34 pm
- Forum: Technical Help
- Topic: Replacing the wrist pin bearing
- Replies: 12
- Views: 6459
Re: Replacing the wrist pin bearing
Was not the bearing. Noise vibration from something else... cover, plate. Anyway it is now gone away.
Thanks!
Thanks!
- Mon Jun 01, 2009 5:27 pm
- Forum: Technical Help
- Topic: Gas not flowing.
- Replies: 7
- Views: 4121
Re: Gas not flowing.
First you said it would run with gas in the bowl but not off the gas line and then you said (last post) it will not run with gas in the bowl. If it runs with gas in the bowl but then runs dry you are not getting gas to the carb and if the petcock works (you sucked on the bottom hose line and gas cam...
- Mon Jun 01, 2009 2:13 pm
- Forum: Technical Help
- Topic: '01 SA50 rough starting
- Replies: 6
- Views: 2841
Re: '01 SA50 rough starting
The carb is pretty greasy and has been leaking oil (blue on the ground) very slightly. The carb should not have any oil in it. That may indicate the problem. Your reeds may be allowing compression to leak back into intake manifold and blow oil into the carb. Check them. They are under the manifold ...
- Mon Jun 01, 2009 11:26 am
- Forum: Technical Help
- Topic: 84 Nifty Fifty won't start
- Replies: 8
- Views: 4044
Re: 84 Nifty Fifty won't start
The petrol is 7 month old 91 octane. How does your country rate octane? That is, what we call regular grade 87 octane in the US is 91 in most of Europe. Is 91 your regular grade gas? If so it is the proper grade for your scooter. Running high octane is not a good idea. If you have Shell in your are...
- Mon Jun 01, 2009 9:14 am
- Forum: Technical Help
- Topic: Gas not flowing.
- Replies: 7
- Views: 4121
Re: Gas not flowing.
Assuming the petcock (gas valve) works when you suck on the bottom hose line the next step is to run a paper clip in and out of the tube (vacuum port) it connects to on the intake manifold. I purchased some used parts recently and this tube was competely blocked on the spare part. No way gas was get...
- Thu May 28, 2009 5:24 pm
- Forum: Technical Help
- Topic: Replacing the wrist pin bearing
- Replies: 12
- Views: 6459
Re: Replacing the wrist pin bearing
Much thanks.
I will try and locate the source using an old stethoscope before I take anything apart.
I will try and locate the source using an old stethoscope before I take anything apart.
- Thu May 28, 2009 2:46 pm
- Forum: Technical Help
- Topic: Replacing the wrist pin bearing
- Replies: 12
- Views: 6459
Replacing the wrist pin bearing
I'm trying to track down a rattle noise on my Spree and have two questions:
The wrist pin bearing is the one at the top of the connecting rod under the piston, correct?
Is it necessary to remove the engine from the Spree in order to replace it?
The wrist pin bearing is the one at the top of the connecting rod under the piston, correct?
Is it necessary to remove the engine from the Spree in order to replace it?
- Fri May 22, 2009 2:43 pm
- Forum: Technical Help
- Topic: Ultrasonic cleaner for the carb?
- Replies: 1
- Views: 1240
Ultrasonic cleaner for the carb?
I've seen videos of this on the web but is anyone here using an ultrasonic cleaner for carbs? I purchased one on Ebay a while back, a nice heavy duty industrial unit, for another application but the next time I need to do a carb I think I'll try it. They say to just use Simple Green and water and it...
- Thu May 21, 2009 1:22 pm
- Forum: Technical Help
- Topic: What's normal take off?
- Replies: 14
- Views: 6292
I cannot take credit for the paint job. The previous owner, a gentleman older than myself... and I'm already old... apparently did it. It was originally a red Spree. I now have large white round Peace symbols on each side over the rear wheel. I also found a new rubber floor mat on Ebay last year and...
- Thu May 21, 2009 9:38 am
- Forum: Technical Help
- Topic: What's normal take off?
- Replies: 14
- Views: 6292
I strapped a Garmin Nuvi to the top of my Spree this morning and did a test ride. According to the Garmin I'm about .5 to 1 mile off on the odometer. The odometer is reading a tad high... as expected. I also did a run with WOT on a level road and got 29.1mph as my top end speed. Also, as expected. N...
- Wed May 20, 2009 4:49 pm
- Forum: Technical Help
- Topic: What's normal take off?
- Replies: 14
- Views: 6292
- Wed May 20, 2009 4:34 pm
- Forum: Technical Help
- Topic: What's normal take off?
- Replies: 14
- Views: 6292