Search found 66 matches
- Wed Mar 31, 2010 11:27 pm
- Forum: Performance Technical
- Topic: ZX trans how-to
- Replies: 192
- Views: 184722
Re: ZX trans how-to
HOPE THIS WRITE-UP HELPS AND MAYBE SOME OTHERS CAN PUT IN THEIR 2 CENTS. (1) BY THE WAY, COVER WILL NEED SHIMMED TO CLEAR OR GET THICKER GASKET FROM ONE OF THE MODELS LISTED. I DO NOT KNOW IF THIS SWAP RENDERS THE STARTER INOP SINCE THE DRIVE PULLEY IS FURTHER AWAY FROM STOCK LOCATION, I DO KNOW TH...
- Wed Mar 31, 2010 10:57 pm
- Forum: General Discussion
- Topic: HondaSpree.net Member Appreciation Sale @ VT Cycles
- Replies: 29
- Views: 12827
HondaSpree.net Member Appreciation Sale @ VT Cycles
Hello fellow HondaSpree.com members, Over the years we have done a lot of business with the members on this forum and speak to some of you on a regular basis. I myself have been a member for a number of years although my participation is lacking due to other commitments. Steve and I have decided to ...
- Wed Mar 31, 2010 10:28 pm
- Forum: General Discussion
- Topic: Daywot missing...again?
- Replies: 27
- Views: 7062
Re: Daywot missing...again?
I know there was a post recently about Patrick not responding to emails because they were going to his Spam folder. But now I have placed an order through Ebay (and an email through Ebay) and have not heard from him in a week. In the past he emailed back and shipped same day, ALWAYS, anyone know if...
- Wed Mar 31, 2010 10:15 pm
- Forum: General Discussion
- Topic: Tripping stop light sensors
- Replies: 25
- Views: 10217
Re: Tripping stop light sensors
I don't have the problem with my current route to work but I used to so I'd just get off the bike and press the button for the cross walk or wait for a car. On a side note, a lot of the lights are set off by breaking the magnetic field set up in the strange squares and circles on the road coming up ...
- Wed Mar 31, 2010 10:05 pm
- Forum: Performance Technical
- Topic: bigger carb?
- Replies: 20
- Views: 7442
Re: bigger carb?
If you are content with the performance of your bike now stick with the stock carb, it will handle your set up with no issues so long as it is jetted correctly. Once you go with a larger carb you tend to have more issues with reliability so that is also something to look at. As far as what size to g...
- Wed Mar 31, 2010 9:44 pm
- Forum: Performance Technical
- Topic: i need a pg exhaust expert...
- Replies: 9
- Views: 4699
Re: i need a pg exhaust expert...
PG Long = Top speed, lots of rev, loud, needs a large carb (28mm works best with it), 3K RPM Clutch Springs, 1500RPM Center Spring, 72cc-110cc engine and $150. PG Short = Better low end than a Long but not as much top speed, large carb needed, same spring set up as a Long, 72cc-98cc engine and $140....
- Sat Jun 13, 2009 7:24 pm
- Forum: Performance Technical
- Topic: Dio Gears? Clearance issues
- Replies: 29
- Views: 9146
Re: Dio Gears? Clearance issues
yeah teh fiber washers hold up just fine, it is an original Honda part that was found in some of the earlier Honda Elite S motors.
- Fri Jun 12, 2009 8:47 pm
- Forum: Performance Technical
- Topic: Malossi or Corsa
- Replies: 6
- Views: 2559
Re: Malossi or Corsa
You can't go wrong with either of them. Buy the cheaper Malossi for your Vino and just make sure you get a Vino exhaust so you don't have to worry about trimming any panels. As for the Polini Corsa, compare it to the Malossi Aluminum cylinder not the cast iron one which most people will do, the Poli...
- Fri Jun 12, 2009 8:39 pm
- Forum: Performance Technical
- Topic: Dio Gears? Clearance issues
- Replies: 29
- Views: 9146
Re: Dio Gears? Clearance issues
Like I said, just sand down the washer a bit lol. Makes for an easy mod...or...you could always get the fiber type washer and put that in instead of the plastic one.
- Fri Jul 18, 2008 12:04 am
- Forum: General Discussion
- Topic: manifold and reeds
- Replies: 3
- Views: 1414
- Thu Jul 10, 2008 8:28 pm
- Forum: General Discussion
- Topic: This is what $370 in parts looks like.
- Replies: 14
- Views: 4178
nparks, stock pulley is fine. keli is nice but having tried lots of various trans combos, I don't find it a critical upgrade. You should get lighter rollers though, 5-6g, maybe lil more with v8 pipe. A hi-speed pulley kit in a Honda Elite S is the single best upgrade you can do. You will never noti...
- Wed Jul 09, 2008 11:38 pm
- Forum: Technical Help
- Topic: Only runs with air filter hose removed
- Replies: 2
- Views: 1186
- Wed Jul 09, 2008 11:02 pm
- Forum: General Discussion
- Topic: Ethanol fuel and Honda Scooters...
- Replies: 8
- Views: 2577
- Wed Jul 09, 2008 10:22 pm
- Forum: General Discussion
- Topic: This is what $370 in parts looks like.
- Replies: 14
- Views: 4178
Thats really odd that the weights were 3 grams 'cause the only 3g rollers we have here are purple unless the factory screwed those up but I'll look into the other packages. we have a very limited number of 9 and 10 gram rollers so if you want them give me a call asap and I'll cut you a deal for the ...
- Wed Jul 09, 2008 5:42 pm
- Forum: Technical Help
- Topic: He says it burns a little bit of oil Is that hard fix?
- Replies: 17
- Views: 5106