Search found 1218 matches
- Sun Dec 04, 2016 1:26 pm
- Forum: Technical Help
- Topic: corsa won't start
- Replies: 29
- Views: 19735
Re: corsa won't start
You have lost 40 in compression. If I saw a reading like that and the bike wouldn't start I would remove and inspect the top end. Sometimes when they are at the bottom of the compression range they just will not start or it is next to impossible to start. Try to do a wet compression check and see if...
- Sat Dec 03, 2016 1:22 pm
- Forum: General Discussion
- Topic: Malossi 94cc 30Hp engine kit giveaway raffle
- Replies: 18
- Views: 10111
- Sat Dec 03, 2016 1:19 pm
- Forum: Technical Help
- Topic: corsa won't start
- Replies: 29
- Views: 19735
Re: corsa won't start
Its been a long time since I did a compression check on that motor but if I recall the compression zone for that engine is 120-160. Your at the lowest end so your prob going to have to open that top up and take a look. I doubt it is the intake. But I could be wrong.
- Mon Nov 21, 2016 12:32 pm
- Forum: Technical Help
- Topic: Piston ring question
- Replies: 12
- Views: 9103
Re: Piston ring question
Did you do a compression test before tearing down the top end? Before you replace the rings make sure to check the gap and also remember to hone the cylinder before you install a new set of ring or piston kit. To check the gap you need a feeler gauge. Don't use those short ones. Use the long feeler ...
- Sat Nov 19, 2016 1:16 pm
- Forum: General Discussion
- Topic: My scooter collection
- Replies: 70
- Views: 46955
Re: My scooter collection
Very nice!! I love how you did the gauge.
Taz
Taz
- Tue Nov 15, 2016 12:20 pm
- Forum: General Discussion
- Topic: Getting the Tazland BBK, GEARS, + MLM ran on a dyno
- Replies: 360
- Views: 172101
Re: Getting the Tazland BBK, GEARS, + MLM ran on a dyno
Lookin Good. Nice paint job. Just so happens I was born in Pitt, PA and its got the colors of the Steelers. * yah
- Sun Nov 06, 2016 10:43 pm
- Forum: Scooter Showcase
- Topic: New MetRukZ 2T 94cc Polini Big Evo build..
- Replies: 30
- Views: 23655
Re: New MetRukZ 2T 94cc Polini Big Evo build..
Looking good Hp. Looking d*** good. Those bars look bad *.
- Fri Nov 04, 2016 1:39 pm
- Forum: Scooter Showcase
- Topic: 35hp 94cc big evo Phanton F12
- Replies: 7
- Views: 7067
Re: 35hp 94cc big evo Phanton F12
d*** that engine is perty
- Sat Oct 29, 2016 1:15 pm
- Forum: Performance Technical
- Topic: full throttle hesitation, only downhill
- Replies: 29
- Views: 15780
Re: full throttle hesitation, only downhill
To pod or not to pod that seems to be the question. I have good results running BBK's with a pod on a stock carb but in Vegas we don't have a lot of hills in town so maybe that is why. Most of the time I used the stock box with the uni breather tabs. I do have bigger pilot jets for the stock carb. T...
- Sun Oct 16, 2016 11:02 am
- Forum: General Discussion
- Topic: How can I buy from a Japan auction?
- Replies: 16
- Views: 12607
Re: How can I buy from a Japan auction?
I have an agent you can use. IM me
Taz
Taz
- Fri Oct 14, 2016 12:49 pm
- Forum: General Discussion
- Topic: How can I buy from a Japan auction?
- Replies: 16
- Views: 12607
Re: How can I buy from a Japan auction?
I use an agent for YahooJapanAuction.
The weather is going to be bad in Seattle. My niece lives there with her 4 kids and she is a bit worried about the wind.
Taz
The weather is going to be bad in Seattle. My niece lives there with her 4 kids and she is a bit worried about the wind.
Taz
- Wed Sep 28, 2016 1:26 pm
- Forum: Technical Help
- Topic: 1984 spree not running, was told bad bearings
- Replies: 8
- Views: 6328
Re: 1984 spree not running, was told bad bearings
sometimes the carbs come loose from the intake mani. If its sputtering then it could be something as simple as a fouled plug as wheel suggested. I have seen bikes idle fine with a foul plug but as soon as you give it gas the bike will sputter and die.
Taz
Taz
- Tue Sep 27, 2016 12:25 pm
- Forum: General Discussion
- Topic: Getting the Tazland BBK, GEARS, + MLM ran on a dyno
- Replies: 360
- Views: 172101
Re: Getting the Tazland BBK, GEARS, + MLM ran on a dyno
I just wanted to touch base on the pilot jet. The pilot jet only controls the 1/4 throttle. It was not suppose to be a magic bullet. The theory is if the pilot is to lean on the 1/4 throttle it could cause heat spikes during de-acceleration when you let off the throttle or slow down into the 1/4 thr...
- Tue Sep 20, 2016 11:19 pm
- Forum: Technical Help
- Topic: Spree Rebuild kit
- Replies: 11
- Views: 8012
- Fri Sep 16, 2016 12:42 pm
- Forum: Technical Help
- Topic: Spree has spark, compression, and gas. Still won't start.
- Replies: 49
- Views: 30855
Re: Spree has spark, compression, and gas. Still won't start
Great job Gary.
Pat is da Man with his great advice.
Thanks for letting us know. People will read this in the future and it is good to know the bike is still running great.
Taz
Pat is da Man with his great advice.
Thanks for letting us know. People will read this in the future and it is good to know the bike is still running great.
Taz