Here's a pix
Search found 84 matches
- Wed Apr 15, 2015 5:53 am
- Forum: Scooter Showcase
- Topic: Thanks Scooter Swap Shop for my build
- Replies: 34
- Views: 22399
- Wed Apr 15, 2015 5:52 am
- Forum: Scooter Showcase
- Topic: Thanks Scooter Swap Shop for my build
- Replies: 34
- Views: 22399
Re: Thanks Scooter Swap Shop for my build
Just finish riding tonight bike turned 15k!!! Idk if that's right, speedo said 66mph but my friend with his supermoto last time he checked he said it was easily passed 70mph with me still pulling away wish I had a GPS on or something accurate. May have to recalibrate vapor tech since I didn't do it ...
- Mon Apr 13, 2015 1:21 am
- Forum: Scooter Showcase
- Topic: Thanks Scooter Swap Shop for my build
- Replies: 34
- Views: 22399
Re: Thanks Scooter Swap Shop for my build
Forgot which main I had at that time but I'm around 118-124 with a fat 50 pilot which got me thinking if I got a leak somewhere. Working with the polini 24pwk with c-clip one up.
- Sun Apr 12, 2015 11:57 pm
- Forum: Scooter Showcase
- Topic: Thanks Scooter Swap Shop for my build
- Replies: 34
- Views: 22399
Re: Thanks Scooter Swap Shop for my build
Well get more pix and videos. Just the file is huge and takes for ever to upload. As for the pipe its a screamer so far I'm @69MPH reving low 10k maybe even lower with a dead center spring which couldnt hold the revs and Temps no higher then 310-320
- Sun Apr 12, 2015 11:43 pm
- Forum: Scooter Showcase
- Topic: Thanks Scooter Swap Shop for my build
- Replies: 34
- Views: 22399
Thanks Scooter Swap Shop for my build
Guess I'll make a build thread on my ped. Most, if not all parts bought from Brandon. Motor specs: 70cc malossi mhr stock port just polished exhaust opening Mhr full counter crank Boost port matched Intake cleaned and slightly opened with lots more room to open Yasuni c16 pipe CT black manifold w/st...
- Sat Mar 21, 2015 3:29 am
- Forum: General Discussion
- Topic: stock s boss lentgh
- Replies: 2
- Views: 1874
stock s boss lentgh
Just as the title says. Need to trim down a zx boss to s length
- Thu Mar 19, 2015 4:56 am
- Forum: General Discussion
- Topic: corsa and mhr boost port
- Replies: 2
- Views: 2412
corsa and mhr boost port
Are the boost port same in size at the base between these two bores. Reason I'm asking is because I have a mhr bore and may want try a corsa again and I'm hoping their the same and not one is bigger than the other. Hopefully someone can asking this.
- Thu Feb 26, 2015 11:06 pm
- Forum: Performance Technical
- Topic: Malossi cast iron port map
- Replies: 0
- Views: 2335
Malossi cast iron port map
Anyone have the specs/port map for a cast iron malossi bore for the dips? Seen the mhr map, just wanna see how much of a difference between the two
- Tue Feb 10, 2015 12:07 am
- Forum: Builder's workshop
- Topic: Polini/malossi pulley
- Replies: 10
- Views: 5670
Re: Polini/malossi pulley
And this is for a dio motor
- Tue Feb 10, 2015 12:04 am
- Forum: Builder's workshop
- Topic: Polini/malossi pulley
- Replies: 10
- Views: 5670
Polini/malossi pulley
Can anyone tell me the difference between the two looking to buy one but could not find good close of pictures of the them. Or if anyone can compare it to a Keli pulley
- Sat Jan 31, 2015 5:03 pm
- Forum: Builder's workshop
- Topic: Gdash / scorpion pipe
- Replies: 0
- Views: 2912
Gdash / scorpion pipe
Anyone on board had any experience with a gdash pipe? Some peeps told me is simallar to a scorpion and a few said its a bit better.
Here's a pic of it http://i13.photobucket.com/albums/a278/ ... w4w9hr.jpg
Here's a pic of it http://i13.photobucket.com/albums/a278/ ... w4w9hr.jpg
- Mon Jan 26, 2015 5:03 am
- Forum: Builder's workshop
- Topic: polini manifold and carb test.
- Replies: 36
- Views: 27241
Re: polini manifold and carb test.
Just curious. Have you ever compaired oko and polini pwk verison of the same size?
- Sat Jan 24, 2015 12:58 am
- Forum: General Discussion
- Topic: ****Official Picture Post...The Sequel****
- Replies: 431
- Views: 285321
Re: ****Official Picture Post...The Sequel****
dd50 sym build
edit.. have to resize image
edit.. have to resize image
- Sat Jan 24, 2015 12:46 am
- Forum: General Discussion
- Topic: ****Official Picture Post...The Sequel****
- Replies: 431
- Views: 285321
- Tue Jan 20, 2015 5:35 pm
- Forum: Builder's workshop
- Topic: polini manifold and carb test.
- Replies: 36
- Views: 27241
Re: polini manifold and carb test.
Just had a few questions on this manifold. Can I use a 24mm pwk style carb on this? What's the diameter of the inlet? And is the reed cage simallar to a ct cage?