48mm Spree BBK(taz)

[tazland001]

Noise the variator you drew up only has a plate design for four rollers? Or am I wrong? The back plate looked like a t.

Now on the yamaha razz upgrade parts. I actually had plans to make some but the 44mm kit for the razz never really took off like the 44mm spree kit.So I figured there was no real demand for upgrades for the razz. It is weird because they sold the razz for like 13 or 14 years in the usa. A lot longer than the spree which was sold for 4 years. But the spree parts sell like wild fire at times and the razz parts do not. To be honest fellas I have made parts in the past when I did hella upgrades at my shop. I made gears for both models of the e-ton beamer before also. I use to upgrade three to four beamers a week at times. I had a e-ton dealer across the street. The e-ton is actually not that bad of a scooter. They where actually pretty popular in Vegas before the recession.

Taz

[tazland001]

I forgot to add a few things on the razz. It is wierd but the razz is actually the yamaha mint in Japan. They produced the mint for only a few years compared to the razz. But the mint was faster than the razz on acceleration. There is one trick for your razz you can do. The kick start cover has gear oil in it. It is because they use a chain. But most people fill the kick starter side up all the way. That is actually a no no. See if it is full the gears float and cause drag you will go slower. If you fill it to about 20% then there is no drag but plenty of lubrication still. This usaully adds better acceleration and in some cases 5mph on the top end. Hope that helps homie.

Taz

[tospreeornottospree]

finally into a true spree...... thanks tjamz! cant wait for the 48 taz only if V-TEC was next!

[jstone]

So should I have any hope left for that expansion chamber pipe I sent you that you said I would get back?

[tazland001]

Actually the pipe will be next. I thought the agreement was you were to get the first pipe for free. Believe me the pipe I make will be much better suited for the spree than yours. The pipe you sent was more like a rough draft and is to small for the 48mm kits. But it gives my makers a good idea of what we are looking for. Do not worry I have not forgot.

Taz

[mustangwagz]

so ur making a pipe for the 48mm kits...

how about the 44's?

[tazland001]

It will not work as well with the 44mm. The 44mm kit is actually just to give you some decent acceleration. It will not have the power the 48mm has. Remeber 44mm is under what I call the punch zone.

[martynkim]

Ok Taz, quit teasing me..... Where is it???

[Trafficjamz]

What is the ETA on the 48mm bbk?

Me and my friends can hardly wait.

[tazland001]

I will have the 48mm BBK in 3 weeks and maybe sooner.

Taz

[martynkim]

Sooner?

[tazland001]

V-tech will never carry these parts. I own all the molds. I will never let anyone else sell these parts except me. mohahahahah.

Taz

[mustangwagz]

V-tech will never carry these parts. I own all the molds. I will never let anyone else sell these parts except me. mohahahahah.

Taz

lol,

so * do you do that you've got access to molten metal and engineers!? i got access to maching equipment and engineres but not molds.. (sighs) Hey, mold up some aluminum petcock covers man! i KNOW you'd sell them!

[Trafficjamz]

Petcock covers don't really exsist.
They are like the unicorns and the tooth fariy. I have heard stories.....but have never actually seen one

[Bear45-70]

Petcock covers don't really exsist.
They are like the unicorns and the tooth fariy. I have heard stories.....but have never actually seen one

You're just not a true believer, I see one every time I look at my Spree.