Greetings:
I honestly don't remember what's in my own OKO 26, but I need to check. It was pretty responsive in the cold weather, but feeling richer as Deepinnaharta warms up. Mainly I wanted this to be post #300 in your thread...
Checkin in, first post... here at least
Moderator: Moderator
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: Checkin in, first post... here at least
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
-
- Elite
- Posts: 507
- Joined: Fri Jun 11, 2010 6:52 pm
- Location: North Bay, CA
Re: Checkin in, first post... here at least
300! woo
Assuming that this UNI is going to act as if there were no air filter on at all (very little restriction)
I think either 50-55 pilot and 120-125 main will work fine. Still having these flooding over bump issues which is a float height adjustment.
I just want to ride this and not worry about tuning anymore!!! never ending...
Assuming that this UNI is going to act as if there were no air filter on at all (very little restriction)
I think either 50-55 pilot and 120-125 main will work fine. Still having these flooding over bump issues which is a float height adjustment.
I just want to ride this and not worry about tuning anymore!!! never ending...
1995 SA50P
pop pulley
50mm Ruima
8.44:1 gears
PG Typhoon
1500k spring
1000k Polini triples
M Keli clutch
28mm Keihin PWK
OKO Polished intake
uni filter
-
- Elite
- Posts: 507
- Joined: Fri Jun 11, 2010 6:52 pm
- Location: North Bay, CA
Re: Checkin in, first post... here at least
I found a 52 pilot in my parts bin.
Swapped that into the carb tonight-
we'll see what happens when this Uni filter shows up this week
Swapped that into the carb tonight-
we'll see what happens when this Uni filter shows up this week
1995 SA50P
pop pulley
50mm Ruima
8.44:1 gears
PG Typhoon
1500k spring
1000k Polini triples
M Keli clutch
28mm Keihin PWK
OKO Polished intake
uni filter
-
- Elite
- Posts: 507
- Joined: Fri Jun 11, 2010 6:52 pm
- Location: North Bay, CA
Re: Checkin in, first post... here at least
patiently waiting an UNI 4200 filter...
1995 SA50P
pop pulley
50mm Ruima
8.44:1 gears
PG Typhoon
1500k spring
1000k Polini triples
M Keli clutch
28mm Keihin PWK
OKO Polished intake
uni filter
Re: Checkin in, first post... here at least
I'm in the same boat, i thought i was done till i went to put the filter on . I got it ordered yesterday.Chicago Ben wrote:patiently waiting an UNI 4200 filter...
2001 Honda Elite
1995 Yamaha Jog
1994 Yamaha Axis
I can't believe
that cop put me
in the backseat
when I clearly
called shotgun.
1995 Yamaha Jog
1994 Yamaha Axis
I can't believe
that cop put me
in the backseat
when I clearly
called shotgun.
- Trafficjamz
- CBR1000RR
- Posts: 5353
- Joined: Tue Jul 14, 2009 7:53 pm
- Location: Eastlake, MI
- Contact:
Re: Checkin in, first post... here at least
are you 100% sure about the bump issue being the float height?
new best 1/8th mile time 9.647 seconds @67.155 mph 310lbs total weight
Re: Checkin in, first post... here at least
If it does not go completely dead it could be the float, not necesisarily the wrong height but since the carb is held on by the rubber to the ct manifold it has no other support so it moves up and down when you hits bumps causing it to run rich at the moment you hit a bump. What I do when i see a bump is I slow down then gas it right as i roll over the bump otherwise it sounds all bubbly
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
-
- Elite
- Posts: 507
- Joined: Fri Jun 11, 2010 6:52 pm
- Location: North Bay, CA
Re: Checkin in, first post... here at least
About 90 % sure. When I hit a bump that I didn't see I have to gas it back again (takes a couple seconds) . I'm going to attempt to adjust the floats so my bowl fill height is about 80-90% of where it currently fills to. Wish adjusting the floats on these carbs wasn't such a guessing game.Trafficjamz wrote:are you 100% sure about the bump issue being the float height?
1995 SA50P
pop pulley
50mm Ruima
8.44:1 gears
PG Typhoon
1500k spring
1000k Polini triples
M Keli clutch
28mm Keihin PWK
OKO Polished intake
uni filter
-
- Elite
- Posts: 507
- Joined: Fri Jun 11, 2010 6:52 pm
- Location: North Bay, CA
Re: Checkin in, first post... here at least
now all I have to do is wait for my friend to drop the moped back off at my place... until next week...
1995 SA50P
pop pulley
50mm Ruima
8.44:1 gears
PG Typhoon
1500k spring
1000k Polini triples
M Keli clutch
28mm Keihin PWK
OKO Polished intake
uni filter