1986 black Spree project
Moderator: Moderator
1986 black Spree project
I purchased a Spree on Friday that I found on craigslist. They didnt tell me that the rings were possibly siezed up but since I drove 100 miles and it was only 50 bucks I went ahead and took it. Got it home and poured a little oil in the spark plug hole I figured if the rings were stuck that would do it but nothing. I took the side cover off and the kickstarter gear was rusted up, got that free and the motor turned fine. Since the oil didnt leak down I figure the rings are fine. I took the carb off and cleaned the gunk out and noticed the bystarter was broken, missing the end needle and the brass was lodged in the carb. Managed to get it out with needle nose. I had to take the starter button off and clean the oxidation. Hooked it up and it turned over easy. I put a little gas in the spark hole and it wanted to start so hopefully my only problem now is the bystarter. I went to the honda dealership today with the ignition in hand and they made me a key on the spot for 5 bucks which saved me from buying a new ignition. I also waxed the plastics hopeing to restore some of the shine, the plastics are faded and sun-damaged in places. If anyone has any suggestions on how to restore the plastics without repainting I am all ears. Imma work on cleaning the rust from the wheel hubs and the muffler tomorrow, the muffler is rusted from start to finish, looks like someone left it sitting in a sagegrass patch for a few years lol
Last edited by Mystic on Mon May 16, 2011 10:21 pm, edited 1 time in total.
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
- spree-rider
- Elite
- Posts: 693
- Joined: Tue Nov 03, 2009 8:24 pm
- Location: Burien, WA
Re: 1986 black Spree project
i used rubbing compound then coats and coats of wax. i spent 11 hours on my panels. They look great. (i only did the rears). After sitting in direct sunlight for 16 straight years.
86 spree
sb 50 intake and reeds
3.00x10 rear tire
waxed
99Polaris indy 700
harliquim paint
2" bar riser
lefty throttle
ice scratchers
SLP tri keel skis
ported
high compression head
chrome low windshield
mountain bar
Xtra-10
I ALWAYS KEEP ONE ROLLED
sb 50 intake and reeds
3.00x10 rear tire
waxed
99Polaris indy 700
harliquim paint
2" bar riser
lefty throttle
ice scratchers
SLP tri keel skis
ported
high compression head
chrome low windshield
mountain bar
Xtra-10
I ALWAYS KEEP ONE ROLLED
Re: 1986 black Spree project
yea i figured I would have to put several coats of wax over a weeks time. The worst part is the front fender. I guess its because it and the back tailight mount are made of solid black plastic instead of coated fiberglass like the majority of the other pieces.
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
- spree-rider
- Elite
- Posts: 693
- Joined: Tue Nov 03, 2009 8:24 pm
- Location: Burien, WA
Re: 1986 black Spree project
goodlocuk on the fender if you plan on waxing it off the bike. And goodluck if you plan to wax it on the bike. lol. it only needed one coat i just put multiples over my stickers. Rubing compound is key.
86 spree
sb 50 intake and reeds
3.00x10 rear tire
waxed
99Polaris indy 700
harliquim paint
2" bar riser
lefty throttle
ice scratchers
SLP tri keel skis
ported
high compression head
chrome low windshield
mountain bar
Xtra-10
I ALWAYS KEEP ONE ROLLED
sb 50 intake and reeds
3.00x10 rear tire
waxed
99Polaris indy 700
harliquim paint
2" bar riser
lefty throttle
ice scratchers
SLP tri keel skis
ported
high compression head
chrome low windshield
mountain bar
Xtra-10
I ALWAYS KEEP ONE ROLLED
- martynkim
- Board Supporter
- Posts: 2899
- Joined: Tue Jan 05, 2010 10:22 pm
- Location: Tacoma, Washington
Re: 1986 black Spree project
Get a mother's ball on a cordless drill with some turtle wax compound. work it around. Good Results..
Need parts? Parting out Spree Aero and Elite!
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
What people share about buying from me http://www.hondaspree.net/phpBB3/viewto ... =1&t=15559
PM me with your needs Cheap Parts
- KillinSpree
- Elite
- Posts: 592
- Joined: Mon Jul 23, 1973 10:24 am
- Location: Sylvania, OH
Re: 1986 black Spree project
For the panels us nufinish scratch doctor in a orange tube and for the rear taillight housing and fender use mothers back to black. Amazing results!
1984 Honda Spree White
1987 Honda Spree Blue
1987 Honda Spree Blue
Re: 1986 black Spree project
I checked out those products KillinSpree and Imma see if they carry any of that at autozone. I'd hate to have to roder off the internet, the shipping is what gets me most of the time. One reason I got the scooter is so these pretty girls I know can go scooting with me cant have them riding around on a junker Especially with me on the C70 passport I know I am awful hahahahha
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
Re: 1986 black Spree project
I took the muffler off and hit it with a wire brush handle till all the dead bugs and stuff fell out. I brushed it till almost all the bristles came outta my brush hahhaha It is super rusty almost no paint left on it. Any ideas on rust removal and paint that wont come off as easy once I start heating it up?
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
-
- Spree
- Posts: 136
- Joined: Fri Dec 10, 2010 10:08 pm
- Location: Milport In.
Re: 1986 black Spree project
I just wire brushed mine also, and used black engine paint. It will stink a bit when you get up to temp. Don't use nitrous in your Spree, it makes the girls fall off!
Re: 1986 black Spree project
Yea I went today and got some of that rustoleum engine paint while I left the muffler primed and drying. Also I found the back to black and nufinish at walmart believe it or not I didnt get the mothers ball it was a bit pricey. I'm young I can use a bit more elbow grease I am considering having my wheels chrome dipped but havent researched that yet I'm sure its expensive. Still it would be nice to have shiny wheels Hopefully the primer I used wont melt off and mess up the black paint but i should have enough left if it does. * imma have it looking brand new before I ever know if it runs or not lol Thanks for all the hints and tips guys. I'll try to post some pics tomorrow of before and after. I am also considering lime green decals and green vinyl for the middle piece of the seat cover not sure yet cause the decals are 35 dollars O.o
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
- KillinSpree
- Elite
- Posts: 592
- Joined: Mon Jul 23, 1973 10:24 am
- Location: Sylvania, OH
Re: 1986 black Spree project
Looking forward to seeing the results
1984 Honda Spree White
1987 Honda Spree Blue
1987 Honda Spree Blue
Re: 1986 black Spree project
Ok I just applied back to black on my front fender, rear taillight assembly and the floorboard waiting for them to dry. may have to second coat the front fender it is pretty bad. I also hit the piece over the back wheel and the fan housing for good measure I applied the first coat of black engine paint to my muffler wish I had taken rusted up pics but i didnt Imma post some pics so yall can have a look see.
--note i was gonna upload more pics but my phone cam takes awesome large pics so i will upload to my facebook wile i sleep and post the link here
--note i was gonna upload more pics but my phone cam takes awesome large pics so i will upload to my facebook wile i sleep and post the link here
- Attachments
-
- This was taken the night i got it :D
- spree.jpg (219.9 KiB) Viewed 8505 times
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
- KillinSpree
- Elite
- Posts: 592
- Joined: Mon Jul 23, 1973 10:24 am
- Location: Sylvania, OH
Re: 1986 black Spree project
Ouch! That seat fovers seen better days. Black spree cover on ebay for $28 shipped i believe
1984 Honda Spree White
1987 Honda Spree Blue
1987 Honda Spree Blue
Re: 1986 black Spree project
I think I am going to get some nagahide/vinyl from the fabric store. Take the cover off, split the seams and trace the damaged piece, cut it out and sew it back together. The back strip with the logo is in good shape just needs some vinyl cleaner on it. Thats how we used to do when we did antique upholstry and the vinyl on boat seat when I worked with this old lady that had an upholstry biz
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
- KillinSpree
- Elite
- Posts: 592
- Joined: Mon Jul 23, 1973 10:24 am
- Location: Sylvania, OH
Re: 1986 black Spree project
Good idea. I have a rear turnsignal rack for that on ebay right now
1984 Honda Spree White
1987 Honda Spree Blue
1987 Honda Spree Blue