here is my sidestand with no welding involved. if you have a bench vise,hammer,drill,drill bits and nuts and bolts, your good to go. you can find the aftermarket sidestand legs on ebay for gy6 scooters for the stylish look. mine uses the bolt for the frame to motor mount. the flat metal bar can be bought from home depot or lowes. the one I'm using is the 2in wide and 1/8in thick
Last edited by bakaracer on Sun Feb 12, 2012 12:18 am, edited 2 times in total.
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Your welcome!!! I figure I share my cheap mods. I post the clamp one for the elites later. I also have the air filter relocation mod for the ct chrome manifold users. How far north of seattle you at?
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Ahh so shoreline lynnwood area. There are a few ruckus guys that ride a lot around there. There is also the seattle scooter meetup group that ride in that area and down to downtown seattle.if your looking for aftermarket scooter parts,check out cycle barn. Those guys bring in parts for the ruckus and zuma.
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
motormike wrote:.......just like the 409....She's Soooooo Fine!!!!.....this Elite falls under the category, "Delicious".....
HAHA! Thanks!
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Here is the clamp style. same like the jdm one for the elite s. The top one is the one from japan. the bottom one is made from flat steel from home depot.
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r
Nice and thanks for th pic and stand source - wiki's updated.
Looks stiiffer than orig. How are you bending those curves to match the frame tube up?
--
mousewheels wrote:Nice and thanks for th pic and stand source - wiki's updated.
Looks stiiffer than orig. How are you bending those curves to match the frame tube up?
--
mousewheels wrote:Nice and thanks for th pic and stand source - wiki's updated.
Looks stiiffer than orig. How are you bending those curves to match the frame tube up?
--
I bent it using a big table vise and hammer.mold it slow and make the curve a little smaller than the frame tube. I'm sure if I had an anvil it would have been faster .
Nothing like getting stroked!
Thanks to my sponsors
Nos Energy Drinks,themopedcompany.com,nwautoevents.com,Cycle Gear
90 honda dio sp 72cc
87 elite 50 s with 86cc watercooled mini stroke
87 elite 50 race bike mhr 72cc
91 yamaha tzr 250r