AF16E Spree swap, summer project!

[Petrock's 1984 Spree]

I thought the bystarter was 2 wire

A green and a yellow

[Trafficjamz]

These wires are for the starter, but do not go to the starter, They get attached to the spree wire harness.




This wire goes to the starter motor.

[Petrock's 1984 Spree]

Correct the green wire and red with a white strip wire are coming from the elite engine and do get cOnnected to the spree harness. I just tapped them off for now because I don't have big enough connectors

That odd ball wire is coming from the elite engine as well. So I gets connected back to the starter motor? Can I just tape that off seeing as my electric start won't work for the time being due to the zx trans mod?

[Trafficjamz]

Correct the green wire and red with a white strip wire are coming from the elite engine and do get cOnnected to the spree harness. I just tapped them off for now because I don't have big enough connectors

That odd ball wire is coming from the elite engine as well. So I gets connected back to the starter motor? Can I just tape that off seeing as my electric start won't work for the time being due to the zx trans mod?

No real reason to tape it. It will not do any harm if left alone.

[Petrock's 1984 Spree]

It's just my way of checking it off the list.

Alright well trying to wire this up with a fractured vertbrae didn't work. I got halfway and then everything locked up. So 4 steroid shots in the spine later and I'll be good to go at it again tomoro!

This is where a lift would be a life saver

[eliteguy50]

This is where a lift would be a life saver

Have a friend throw it up on a card table for you. Been there with back problems and I've found that works best. Tall enough to use a roller stool to swing around side to side but short enough you can reach the controls on the handlebars.

[Petrock's 1984 Spree]

Good call!

[Petrock's 1984 Spree]

The v8 tyhpoon and exhaust gaskets arrived today!

So once I get the wiring finished I can fire it up. Which brings up now where to jet it. I'm guessing I should jet on the rich side so how does 43, 140 sound?

Polini corsa
21mm carb with CT mani
k&n metal mesh air filter
V8 Typhoon exhaust

[Trafficjamz]

The v8 tyhpoon and exhaust gaskets arrived today!

So once I get the wiring finished I can fire it up. Which brings up now where to jet it. I'm guessing I should jet on the rich side so how does 43, 140 sound?

Polini corsa
21mm carb with CT mani
k&n metal mesh air filter
V8 Typhoon exhaust

way too rich

try 120 main and 48 pilot

[fastplastic]

that still might be a lil right but a good starting point

[Petrock's 1984 Spree]

Baka has me starting at 115
I'll probably use a 45

Once these jets come in I'll be in business!

[Petrock's 1984 Spree]

Got it running now!

P1010974 by jpetrak, on Flickr

P1010975 by jpetrak, on Flickr
I assume this temp is alright for a scoot with this set up all warmed up without the shrouds on it

P1010980 by jpetrak, on Flickr

How does it sound? Anything jump out at anyone that might needed to be adjusted slightly or is it pretty good for some heat cycles?
http://www.flickr.com/photos/58369736@N06/5784057962/

[SpreeMadness520]

, Look at my pic for the oil reserve tank, I put spacers for the tail light so it doesnt rub. Looks good too.

P.S. The front forks look SWEET

[Petrock's 1984 Spree]

, Look at my pic for the oil reserve tank, I put spacers for the tail light so it doesnt rub. Looks good too.

P.S. The front forks look SWEET

I was gonna make my own custom gas tank to fit the rear rack so i hacked up my oil tank to get the sensor out so i could use that as my reserve tank gauge
Need to get those washers too.
Haha oh yes, the forks are worth every bit of effort to fit em on there
I let it idle now for 10-15 minutes and the temp climbed slowly up to 330 F before i shut it off.
Isn't a little toasty just for idle? Maybe a little lean?

Still have the shrouds off it though so maybe not

[SpreeMadness520]

I will eventually put the elite forks on, But I need to get the bbk and other extremities first.