Hey Guys,
Sorry for the late response. I have been at work and no scoot time. I painted the scooter with flat rattle cans...nothing too special. As far as the whitewalls, I got those from www.scooterworks.com.
I have been riding the scoot just around the block at 25 mph or less. I am not able to get more than about quarter throttle and then the motor sputters. trying to wrap my head around it. some carb issues but dont know what. Any ideas?
Thanks!
my first build: 1985 Aero 50
Moderator: Moderator
Re: my first build: 1985 Aero 50
2007 Elite 80
1985 Aero 50
1985 Aero 50
Re: my first build: 1985 Aero 50
are there any differences between the carbs from '85 to '87? I am thinking of buying one and found a couple that say fits the "'86-'87" models. It sure looks the same as mine but dont know for sure...
2007 Elite 80
1985 Aero 50
1985 Aero 50
Re: my first build: 1985 Aero 50
The 1985 fits only the 1985. The 1986 and 1987 used the same carb. The 1983 and 1984 carbs were smaller.
Last edited by Bear45-70 on Sun Nov 06, 2011 12:06 am, edited 1 time in total.
Bear 45/70
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
Re: my first build: 1985 Aero 50
....Hey Bear....check your previous post for typos...i read it and not making sense..... ........
........i.e......"the 1986 fits only the 1985".....
........i.e......"the 1986 fits only the 1985".....
- Attachments
-
- Bear Biker.jpg (21.57 KiB) Viewed 2043 times
RideRed
<(2)Gyro S><Helix><Sym Wolf>
"Live Large - Ride Small"
<(2)Gyro S><Helix><Sym Wolf>
"Live Large - Ride Small"
Re: my first build: 1985 Aero 50
You could try taking the main jet out and rev it on the stand. If it still sputters try moving the clip on the main needle till you can twist to 3/4ths smoothly then reinstall the main and rev it to full to see how the response is IF after you take the main out it doesnt sputter then you may need a larger main or clean the main emulsion tube. Assuming you dont have any air leaks and you have the carb adjusted right
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma