nq50 + Polini Pipe See the video
Moderator: Moderator
nq50 + Polini Pipe See the video
http://youtu.be/XcXYHW5GXuw
I was thinking of doing the big bore 48 kit from chopchop
I will post a video of the plastics soon, I had to do some trimming to fit over/ around the pipes.
I was thinking of doing the big bore 48 kit from chopchop
I will post a video of the plastics soon, I had to do some trimming to fit over/ around the pipes.
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: nq50 + Polini Pipe See the video
boy that a good job!!!!!
swimmingfree
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
Re: nq50 + Polini Pipe See the video
Thanks, I will clean it up a bit more later and post some stuff.swimmingfree wrote:boy that a good job!!!!!
swimmingfree
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: nq50 + Polini Pipe See the video
your 35 is that a gps speed ????
what else have you done to the old girl??
one thing you can do is put a taller tire on it..
swimmingfree
what else have you done to the old girl??
one thing you can do is put a taller tire on it..
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
Re: nq50 + Polini Pipe See the video
Swell job on the mod, deuce.....what have you done with Express ?...I see in your avatar similar ones....I have an '81 that I want to kit with a Hobbit bbk and pipe.
- Attachments
-
- DSC00253.JPG (164.8 KiB) Viewed 5046 times
RideRed
<Gyro S><MB5><Honda Navi><Helix><Sym Wolf><Yamaha Razz><Honda CH150 Deluxe>
"Live Large - Ride Small"
<Gyro S><MB5><Honda Navi><Helix><Sym Wolf><Yamaha Razz><Honda CH150 Deluxe>
"Live Large - Ride Small"
Re: nq50 + Polini Pipe See the video
No not gps. But this thing has hit 38mph bone stock other than the pulley mod I did.swimmingfree wrote:your 35 is that a gps speed ????
what else have you done to the old girl??
one thing you can do is put a taller tire on it..
swimmingfree
I removed the head gasket and used rtv which shaves a few thousandths for more compression too. I also did a mild port job on the jug.
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
- swimmingfree
- CBR1000RR
- Posts: 3357
- Joined: Tue Jun 14, 2011 12:28 pm
- Location: mich.
Re: nq50 + Polini Pipe See the video
not sure but i think you cood put a 3inch tire on it with some grinding but a 2.27 i believe you wont need to grind it that will give you a little more top end speed ..but tack off will be a little slower .. the bbich of a spree is it is what it is ..
swimmingfree
swimmingfree
handicap (dyslexia)
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
looking for
se50 crank...
SpreJunk 87elite in a spree body
ruckus variator , 3.5 tire , 1500 drive face spring , a 64 bbk ,
8 gram rollers, stock carb , after market air filter and 105 jet
Re: nq50 + Polini Pipe See the video
deuce217 wrote:No not gps. But this thing has hit 38mph bone stock other than the pulley mod I did.swimmingfree wrote:your 35 is that a gps speed ????
what else have you done to the old girl??
one thing you can do is put a taller tire on it..
swimmingfree
I removed the head gasket and used rtv which shaves a few thousandths for more compression too. I also did a mild port job on the jug.
38 mph is not possible with a stock NQ50, but then yours is NOT stock. What kind of RTV because the regular stuff will never hold the cylinder pressures?
Bear 45/70
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
Re: nq50 + Polini Pipe See the video
I used HONDABOND rtv, I have never had any trouble with it leaking. I also used for a honda rebel 250cc rebuild this year. I had no issues there either. http://www.ebay.com/itm/OEM-Genuine-HON ... 5ae3cd6e07Bear45-70 wrote:deuce217 wrote:No not gps. But this thing has hit 38mph bone stock other than the pulley mod I did.swimmingfree wrote:your 35 is that a gps speed ????
what else have you done to the old girl??
one thing you can do is put a taller tire on it..
swimmingfree
I removed the head gasket and used rtv which shaves a few thousandths for more compression too. I also did a mild port job on the jug.
38 mph is not possible with a stock NQ50, but then yours is NOT stock. What kind of RTV because the regular stuff will never hold the cylinder pressures?
I am not sure about the stock stuff, I never change anything but the pulley mod and cleaned the carb.
I ordered the 48mm kit from chopchop today and the carb he sells as well. I will keep everybody updated.
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
- KillinSpree
- Elite
- Posts: 592
- Joined: Mon Jul 23, 1973 10:24 am
- Location: Sylvania, OH
Re: nq50 + Polini Pipe See the video
Very cool! I will be following your progress
1984 Honda Spree White
1987 Honda Spree Blue
1987 Honda Spree Blue
Re: nq50 + Polini Pipe See the video
KillinSpree wrote:Very cool! I will be following your progress
See my other threads, the project is moving right along.
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)