Malossi mhr build spreedio 98%

Downsouthdio · Post by **Downsouthdio** » Tue Feb 21, 2012 9:40 pm

if you dont mind..could you get me the part numbers for the bearings and seals?

kingkamehameha · Post by **kingkamehameha** » Tue Feb 21, 2012 10:01 pm

Google

kingkamehameha · Post by **kingkamehameha** » Fri Feb 24, 2012 2:20 am

Comin along

Ali'iNUI · Post by **Ali'iNUI** » Fri Feb 24, 2012 3:01 am

i like buy dat block 100?

swimmingfree · Post by **swimmingfree** » Fri Feb 24, 2012 8:31 am

kingkamehameha
not trying to be a but head ... i wish you wood only have one post on this motor in stead 4 or 5 .. if your doing something i as will as other read a long ..weather we post or not.. i like how you open up the ports and how you did it with a hack saw and this prove you dont need a lot of tools to mod one of this motors .. but with all 4 or 5 people will have have a hard time finding it..

i feel it wood help other that want to build a motor like yours if you had it all on one post ..
swimmingfree

ps
your doing a grate job keep it up ..

kingkamehameha · Post by **kingkamehameha** » Fri Feb 24, 2012 1:24 pm

That what i was thinkin too swimming free. Thanks for the compliments

kingkamehameha · Post by **kingkamehameha** » Tue Feb 28, 2012 2:32 am

Crank and bore on. Just need to finish the rest after work tommorow. For some reason i couldnt get my clutch bell to fit on the primary. It fits in my stock primary shaft fine but it had trouble going onto the aftermarket one. Any suggestions?

kingkamehameha · Post by **kingkamehameha** » Wed Feb 29, 2012 3:26 am

Did some polishing

paulpauly7 · Post by **paulpauly7** » Wed Feb 29, 2012 4:45 am

TACOS yum thats making me hungary your tranny case looks good too

Wheelman-111 · Post by **Wheelman-111** » Wed Feb 29, 2012 9:10 am

Greetings:

Studies show that 4 out of 5 Oral Hygienists agree that nothing makes your tranny cover shine better than Colgate. Make sure you use some after the Tacos.

Nice work on the case.

kingkamehameha · Post by **kingkamehameha** » Wed Feb 29, 2012 11:09 am

Thanks wheelman. Yeah i just used toothpaste cause i ran out of aluminum polish. Im gonna go down today and get some after work

eliteguy50 · Post by **eliteguy50** » Thu Mar 01, 2012 2:35 am

kingkamehameha wrote: Crank and bore on. Just need to finish the rest after work tommorow. For some reason i couldnt get my clutch bell to fit on the primary. It fits in my stock primary shaft fine but it had trouble going onto the aftermarket one. Any suggestions?

Get the driven pulley from the engine those gears were made for.

Red Eft Performance · Thu Mar 01, 2012 10:07 am

Looking good! Be sure and take the time to pressure test that motor!

kingkamehameha · Post by **kingkamehameha** » Sat Mar 03, 2012 10:44 pm

Almost ready

kingkamehameha · Post by **kingkamehameha** » Sun Mar 04, 2012 5:55 pm

Pulled the spree motor out today. I only had a little bit of time to work on it today. Hopefully i can get the new mount fitted and shock mount relicated in the next few days

Honda Spree and Elite 50 Forums

Malossi mhr build spreedio 98%

Re: Malossi mhr build sneak peak

Re: Malossi mhr build sneak peak

Re: Malossi mhr build sneak peak

Re: Malossi mhr build sneak peak

Re: Malossi mhr build sneak peak

Re: Malossi mhr build sneak peak

Re: Malossi mhr build sneak peak

Re: Malossi mhr build sneak peak

Re: Malossi mhr build spreedio!!!!!!

4 Out of 5 Dentists Agree

Re: Malossi mhr build spreedio!!!!!!

Re: Malossi mhr build sneak peak

Re: Malossi mhr build spreedio!!!!!!

Re: Malossi mhr build spreedio!!!!!!

Re: Malossi mhr build spreedio!!!!!!