Japanese "Fine Selection" Jog

[tru72]

heres my baby...

[Downsouthdio]

Wow that is nice..

[tazland001]

Heck yah. The 3KJ jog. Lots of parts for that scoot
d*** Tru you always get the cleanest scooter. d*** you. lol

As far as customs go the rules are
Any scooter over 25 years old is exempt to DOT
Any scooter is automatically exempt to EPA if under 50cc.

Some of the early jogs can be imported with no problems at all.

I would love to find a yamaha passola(sa50).

Taz

[tru72]

hehe thanks taz!!

You know what i really want is a Jog RR or a aerox

[DaylightDies]

Heck yah. The 3KJ jog. Lots of parts for that scoot
d*** Tru you always get the cleanest scooter. d*** you. lol

As far as customs go the rules are
Any scooter over 25 years old is exempt to DOT
Any scooter is automatically exempt to EPA if under 50cc.

Some of the early jogs can be imported with no problems at all.

I would love to find a yamaha passola(sa50).

Taz

I can't say I have seen to many in running condition. lol

They have alot of Jog 90s here too, I havn't seen many aeroxs.

[DaylightDies]

Just scored my Japanese Jog for $400!

Pics will come in two weeks when I pick it up from the shop.

[DaylightDies]

Pictures are up! The exhaust is horrible!!!! I will be getting a new one shortly, just trying to decide what to buy.

[DaylightDies]

Pretty sure this case has not been opened in over a decade!
Currently cleaning up the old parts while I debate on ordering new parts.
I know for sure that I will be ordering at least new reeds.

Here are some "before" pics.


Covered in dust from the plastic cover that was sealed on top of the case.


Bell looks like it was rubbing.


Cracked open the crank case and all that dust/sand exploded onto the tire.


Carb bowl was filled with a nasty film of some plastic-type substance. It is currently soaking in carb cleaner.


Grease is half an inch to an inch thick covering most of the case. I have two degreasers, and naval jelly to clean up the whole engine!



19mm sockets are a killer! But I think I have a tool that will help me hold the clutch in place (a belt-grip wrench).

[veedubh20]

http://i.imgur.com/GUXK0.jpg. Here are the tool you needs.

[DaylightDies]

http://i.imgur.com/GUXK0.jpg. Here are the tool you needs.

Yup I will be picking those exact tools up during the week. Currently, I have the tire off and the brake pads are non existent!
Do you guys know where I can buy rims? I would actually like to purchase new ones and "Pimp-my-scoot".

[veedubh20]

well. they dont have any aftermarket rims for front drum brake. unless you should go front disk conversion.. will cost you more!

[DaylightDies]

I found a few good places. I mainly want to replace the rear, but I will be converting to front discs because it will cost me less then 100$ for the conversion here lol

[deuce217]

I found a few good places. I mainly want to replace the rear, but I will be converting to front discs because it will cost me less then 100$ for the conversion here lol

Must be nice! Cool deals man.

[veedubh20]

I found a few good places. I mainly want to replace the rear, but I will be converting to front discs because it will cost me less then 100$ for the conversion here lol

should have wait and bought a jog evolution zr than a jog beater.

[DaylightDies]

I found a few good places. I mainly want to replace the rear, but I will be converting to front discs because it will cost me less then 100$ for the conversion here lol

should have wait and bought a jog evolution zr than a jog beater.

I wanted a 3KJ I might buy a honda ns50 and a few other things while I am here. We shall see.
Also, I don't want a 4 stroke.