85 Spree CVT
Moderator: Moderator
85 Spree CVT
So can somebody post a link to why the 85 spree coes not have a CVT style pulley on the rear... Is a snowmobile clutch not considered a type of CVT. Feel free to flame, I am not sure exactly how my rear pulley works as I have not but my cover in half to watch it in operation.
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
- Trafficjamz
- CBR1000RR
- Posts: 5353
- Joined: Tue Jul 14, 2009 7:53 pm
- Location: Eastlake, MI
- Contact:
Re: 85 Spree CVT
The rear pulley on your spree acts more like a belt tensioner than a cvt.deuce217 wrote:So can somebody post a link to why the 85 spree coes not have a CVT style pulley on the rear... Is a snowmobile clutch not considered a type of CVT. Feel free to flame, I am not sure exactly how my rear pulley works as I have not but my cover in half to watch it in operation.
The ratio of the spree's front to rear pulley ratio stays the same while you ride it.
spree= the one speed wonder
new best 1/8th mile time 9.647 seconds @67.155 mph 310lbs total weight
Re: 85 Spree CVT
d***, that makes sense. Thanks for clearing that up, sometime I will try to make a custom front one then, when I do you guys will get to enjoy it too.Trafficjamz wrote:The rear pulley on your spree acts more like a belt tensioner than a cvt.deuce217 wrote:So can somebody post a link to why the 85 spree coes not have a CVT style pulley on the rear... Is a snowmobile clutch not considered a type of CVT. Feel free to flame, I am not sure exactly how my rear pulley works as I have not but my cover in half to watch it in operation.
The ratio of the spree's front to rear pulley ratio stays the same while you ride it.
spree= the one speed wonder
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
- Trafficjamz
- CBR1000RR
- Posts: 5353
- Joined: Tue Jul 14, 2009 7:53 pm
- Location: Eastlake, MI
- Contact:
Re: 85 Spree CVT
deuce217 wrote: d***, that makes sense. Thanks for clearing that up, sometime I will try to make a custom front one then, when I do you guys will get to enjoy it too.
If you have a 1986 or 1987 spree, you can fit in a crank from a se50 scooter, and use it's variator.
The down side to this is, the rear pulley in the spree does not line up, and the kicker cover will not fit .
I almost got it all worked out I used a rear pulley from an urban express.
But I need a custom shaft to let it mesh with the spree gears.
new best 1/8th mile time 9.647 seconds @67.155 mph 310lbs total weight
- tazland001
- Board Supporter
- Posts: 1333
- Joined: Thu Apr 30, 2009 11:46 pm
Re: 85 Spree CVT
I was going to build one of these up to. I actually have a new crank that goes into the honda pal with a variater. My problem is the same. On the pal it had a longer arm for the clutch so the belt was even with the drive face/driven face. I have been looking for one of these pal engines but they are suppppppper rare. I have only seen 3 and had no clue at the time what I had.
Mouse is there anyway you could find anything out on that certain pal engine with a variater??
Taz
Mouse is there anyway you could find anything out on that certain pal engine with a variater??
Taz
-
- Veteran OG
- Posts: 3639
- Joined: Tue May 22, 2007 8:10 pm
- Location: North of Seattle, WA
Re: 85 Spree CVT
Getting close there 'jamz.
I don't know where to get variated Pal parts, but will look. I remember keithw had one...Mouse is there anyway you could find anything out on that certain pal engine with a variater??
Re: 85 Spree CVT
mousewheels wrote:Getting close there 'jamz.
I don't know where to get variated Pal parts, but will look. I remember keithw had one...Mouse is there anyway you could find anything out on that certain pal engine with a variater??
Right on Mouse!
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
Re: 85 Spree CVT
yahoo auctions japan has all your so called hard to find parts
DJ1
NEK MINNIT
Malossi
DJ1 54mph
dio gear swap in progress
living in chch NZ
earthquake central
NEK MINNIT
Malossi
DJ1 54mph
dio gear swap in progress
living in chch NZ
earthquake central