1983 Aero 50 hard start when cold

spree picker · Post by **spree picker** » Tue Sep 27, 2011 9:40 am

I PICKED UP A 83 aero with 795 miles runs great after I get it started but when it sits for awhile hard to start very long crank if i give it any gas it dies,after several tries it starts

swimmingfree · Post by **swimmingfree** » Tue Sep 27, 2011 9:46 am

you bystarter may be bad..
do a compression test as well it wont hurt..
swimmingfree

spree picker · Post by **spree picker** » Tue Sep 27, 2011 9:48 am

the bystarter test good like 5 ohms

swimmingfree · Post by **swimmingfree** » Tue Sep 27, 2011 10:01 am

im no you read it a lot but clean the carb... if the hole blow the bystarter is plug it may be what is going on
swimmingfree

Mystic · Post by **Mystic** » Tue Sep 27, 2011 10:20 am

I agree with swimming free, also check to make sure the o-ring on the bystarter isnt cracked or damaged

RZRob · Post by **RZRob** » Tue Sep 27, 2011 10:29 am

I've got two '83s and they both have this problem. One though, after riding it more frequently, the problem seems to be subsiding. Either way, when you clean the carb, note the pinhole orifice in the float bowl, and the emulsion tube that just presses in the carb under the mainjet. These are both easily overlooked. I think air screw setting may have helped too.

RZ Rob

spree picker · Post by **spree picker** » Tue Sep 27, 2011 10:56 am

I will reclean tonight thanks

swimmingfree · Post by **swimmingfree** » Tue Sep 27, 2011 11:02 am

there is a small hole you can see when you look now were the slide goes its the hard part to get clean if you cant see thou it its not clean anuff use compress air or a spray cleaner to make sure its clean
swimmingfree

spree picker · Post by **spree picker** » Tue Sep 27, 2011 9:21 pm

Ok,took carb apart everything got blown out good will put back together tomorrow.I didn't seen any restriction wish me luck!

Bear45-70 · Post by **Bear45-70** » Tue Sep 27, 2011 9:52 pm

RZRob wrote:I've got two '83s and they both have this problem. One though, after riding it more frequently, the problem seems to be subsiding. Either way, when you clean the carb, note the pinhole orifice in the float bowl, and the emulsion tube that just presses in the carb under the mainjet. These are both easily overlooked. I think air screw setting may have helped too.

RZ Rob

1983's??????? I don't think so.

Wheelman-111 · Post by **Wheelman-111** » Tue Sep 27, 2011 10:03 pm

Greetings:

Bear, Why doubt ye the eighty-three? Could be '84s I guess. One thing's for sure: They're WAAAAYY cleaner than any scooter that old has any right to be! Nice quiver, RZ.

spree picker · Post by **spree picker** » Tue Sep 27, 2011 10:22 pm

looks like 83 to me,as far as clean * yea I have 2 84 gyros and 2 85 sprees just as clean.Very nice collection thanks for the pics.

Bear45-70 · Post by **Bear45-70** » Tue Sep 27, 2011 10:58 pm

Because I didn't look close at the picture and it bit me in the butt.

spree picker · Post by **spree picker** » Fri Sep 30, 2011 7:17 am

soaked and cleaned,rode last night .It started up this morning looks like I'm riding the old girl to work.

Honda Spree and Elite 50 Forums

1983 Aero 50 hard start when cold

1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold

Re: 1983 Aero 50 hard start when cold