Page 1 of 1

CT Manifold

Posted: Sun Aug 19, 2012 11:04 pm
by DaylightDies
The CT intake manifold is typically for bigger carbs, 24mm+ but I want to use it with a small Carb. is there a way to make the Carb output bigger? or to make the intake smaller?

Re: CT Manifold

Posted: Sun Aug 19, 2012 11:28 pm
by Bear45-70
DaylightDies wrote:The CT intake manifold is typically for bigger carbs, 24mm+ but I want to use it with a small Carb. is there a way to make the Carb output bigger? or to make the intake smaller?
Where did you get that idea? It will work with anything you want to mount on it, even a stock carb.

Here is a CT with an 18mm carb off an Aero 125 for my 1985 Aero 50 with a mini BBK (43mm).

Image

Re: CT Manifold

Posted: Mon Aug 20, 2012 12:10 am
by DaylightDies
=-O I didn't know they can tighten down that much. Thank you bear!

Re: CT Manifold

Posted: Mon Aug 20, 2012 12:12 am
by veedubh20
jog dont need pwk21-28mm carb. suck more petrol fuel and make more noise! :lol:

dellorto phbg carb is good enough.

my jog dont have problem and start 1 kick always ran 12mm carb on polini bore.


im sure the pe/pwk carb will rub the main frame, not much room for run airbox.

Re: CT Manifold

Posted: Mon Aug 20, 2012 12:15 am
by Bear45-70
DaylightDies wrote:=-O I didn't know they can tighten down that much. .......................
What does tighten down mean?

Re: CT Manifold

Posted: Mon Aug 20, 2012 12:21 am
by DaylightDies
The hose clamps on the intake of the manifold. @veedubh 12mm is kind of small and it is very hot here I think 17.5mm is the smallest ill go on a bbk.

Re: CT Manifold

Posted: Mon Aug 20, 2012 12:25 am
by Bear45-70
DaylightDies wrote:The hose clamps on the intake of the manifold. @veedubh 12mm is kind of small and it is very hot here I think 17.5mm is the smallest ill go on a bbk.
No, you can't tighten the hose clamp extra, beside the smaller carb has to bolt up to something, so you have an adapter made. Look closely at my pic and you will see the carb bolted to the adapter that plugs into the rubber.

Re: CT Manifold

Posted: Mon Aug 20, 2012 1:33 am
by DaylightDies
ahhh I see, what if my Carb doesn't have the flange like yours does?

Re: CT Manifold

Posted: Mon Aug 20, 2012 2:00 am
by veedubh20
the bws 100 is 16mm teikei carb is 16mm.

all the jog carb 12,14,16mm on the rear carb inlet pipe of a carb is 18mm. ( not talking about the outside pipe mount).

Re: CT Manifold

Posted: Mon Aug 20, 2012 7:47 am
by Mystic
you can get a 17.5mm dellorto cloned carb for around 30 bucks :D

Re: CT Manifold

Posted: Mon Aug 20, 2012 9:06 am
by DaylightDies
Mystic wrote:you can get a 17.5mm dellorto cloned carb for around 30 bucks :D
:O PM pls!

Re: CT Manifold

Posted: Mon Aug 20, 2012 10:46 am
by Downsouthdio
Arreche 17.5 or 19mm,

Re: CT Manifold

Posted: Mon Aug 20, 2012 10:52 am
by DaylightDies
Downsouthdio wrote:Arreche 17.5 or 19mm,
I liked my 19mm Arreche on my Jog in the states. I would like to get a 17.5mm Arreche.