9 to 1 gears set
http://www.ebay.com/itm/Honda-Elite-S-S ... e6&vxp=mtr
is that good one? I have 2001 honda elite 50 sr the black one. af16 engine...
is it ok to use 9:1 gears set for 50cc stock and 75cc kit too? I have 75cc kit I will put it on later...
9:1 gears set
Moderator: Moderator
-
micbergsma
- Spree
- Posts: 115
- Joined: Sat Dec 18, 2010 9:06 pm
- Location: Maui Hawaii
- Contact:
9:1 gears set
Scooter videos on YouTube: http://bit.ly/2fK6kHJ
Website: http://bit.ly/2gvBRyI - Scooter IG: http://bit.ly/2fB8gay
Website: http://bit.ly/2gvBRyI - Scooter IG: http://bit.ly/2fB8gay
-
micbergsma
- Spree
- Posts: 115
- Joined: Sat Dec 18, 2010 9:06 pm
- Location: Maui Hawaii
- Contact:
Re: 9:1 gears set
that's me on my elite - all stock, went 40mph on the curve it was fun!
- Attachments
-
- that's me!
- micelitelean.jpg (203.5 KiB) Viewed 4141 times
Scooter videos on YouTube: http://bit.ly/2fK6kHJ
Website: http://bit.ly/2gvBRyI - Scooter IG: http://bit.ly/2fB8gay
Website: http://bit.ly/2gvBRyI - Scooter IG: http://bit.ly/2fB8gay
-
Wheelman-111
- Moderator
- Posts: 11319
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: 9:1 gears set
Greetings:
9:1 is pretty good on a stock block if it's producing good power. Mine went 49 with ZERO Engine mods, only the gears and a big variator and tire. Once you big-bore, the 9s will be a little short. You'll regain faster-than-stock take-off but it won't increase your speed very much unless the Big-Bore can rev higher than stock. At that point, you may want to swap again for 8.44s or whatever your riding needs and engine power dictate.
9:1 is pretty good on a stock block if it's producing good power. Mine went 49 with ZERO Engine mods, only the gears and a big variator and tire. Once you big-bore, the 9s will be a little short. You'll regain faster-than-stock take-off but it won't increase your speed very much unless the Big-Bore can rev higher than stock. At that point, you may want to swap again for 8.44s or whatever your riding needs and engine power dictate.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
9:1 gears set
You can put them on with the stock bore and they will do fine but it won't be very whippy on acceleration. As for with the kit, you will probably be fine to use them but depending on the kit, you may want something a little taller. Don't forget to upjet!
1987 Spree
1994 Elite SR
1994 Elite SR
Re: 9:1 gears set
Am I wrong that these will fit in a af50e motor with some shimming?
-
eliteguy50
- CBR1000RR
- Posts: 4219
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: 9:1 gears set
Yes, that is assumption is wrong.CG Elite wrote:Am I wrong that these will fit in a af50e motor with some shimming?
motormike wrote:Errands become adventures.
Re: 9:1 gears set
You are wrong about that. Read this to see whats really needed:CG Elite wrote:Am I wrong that these will fit in a af50e motor with some shimming?
http://www.hondaspree.net/phpBB3/viewto ... =8&t=11792
1986 Spree w/ '87 SE50 motor
1985 Aero 50 w/ Dio motor: On Hold
1985 Aero 50 w/ Dio motor: On Hold