Page 1 of 2

I need tips elite sa50

Posted: Sun Nov 03, 2013 8:52 pm
by 12gauge
72cc Polini corsa,v8 muffler, 24mm oko carb (reed and intake came with), eBay special variator, 9to 1 gear set, eBay special cdi, no plastics on enging or anywere else. Haven't installed head yet scared to over heat. Do u think it will can I get a couple tips to make run great Jet size? I have 115-135 up by fives. Just don't know witch to use. Plastics? Or no I cut out my whole seat bucket and put 10" radiator fan but it kills my batteri

Re: I need tips elite sa50

Posted: Sun Nov 03, 2013 9:22 pm
by bfowler
You could start with a 125 main and 45 pilot and see how that works. Plug chops and CHT gauge are really useful in determining jet sizes.

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 6:48 am
by 12gauge
I no there is no radiator I am useing the fan instead of the shrouds

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 6:49 am
by 12gauge
Wat exactly is a plug. Chop and how do u instal thermostat

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 6:52 am
by 12gauge
And it didn't come wit pilots. But the main is way longer than a normal main jet I haven't taken bowl off to see wats in it

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 6:55 am
by 12gauge
Nvm I no how to install cht I wasn't thinking. Wat temp should I be trying to get. With my set up

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 12:14 pm
by paulpauly7
your fan wont cool the motor.Reinstall the original engine covers and factory fan.Or say bye bye to your corsa

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 12:16 pm
by bfowler
paulpauly7 wrote:your fan wont cool the motor.Reinstall the original engine covers and factory fan.Or say bye bye to your corsa
+1 on this. Fan shrouds are important!

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 3:19 pm
by 12gauge
On the corsa does the ports on piston go toward exaughst or rear wheel

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 3:26 pm
by 12gauge
Graphite. It did come with mains and I only ran 1/4 tank 16 to one premix in it I don't have oil pump At that time I had stock carb with 102 jet. I siezed motor because the cylinder was honed hoe ably and rings were way to loose the exhaust port ate the ring off first time I half throttled it I would put shoud back on but don't have one

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 8:44 pm
by 12gauge
I rebuild motors all the time just not proformance motors I no about rings and pistons the kit. I got from chop chop was * up believe me I did it all right the cylinder was egg shaped almost the rings and piston weren't the right size. I new they weren't wen I was putting it together but I figured that's just how it had to be for some * up reason

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 8:59 pm
by 12gauge
I've been trying I have I phone 4 and if won't let me upload pics says to many kig

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 9:02 pm
by paulpauly7
you shouldnt have run it

Re: I need tips elite sa50

Posted: Mon Nov 04, 2013 9:14 pm
by 12gauge
We'll now I have an amazing loo liking Polini kit I hope I can fine motor shrouds asap I WANA RIDE

Re: I need tips elite sa50

Posted: Tue Nov 05, 2013 2:51 pm
by kingearwig
upload your pics to photobucket.com then use the photobucket provided <img tag