Does your Spree/Elite already run great, and you're trying to make it quicker/faster? Need a monster motor swap? Discuss your ideas here.
Moderator: Moderator
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Mon May 12, 2008 6:45 am
so for once the secretary of state right, my bike is an 1981 not 1983
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express
burnt_toast
Veteran OG
Posts: 3592 Joined: Sat Jul 31, 2004 8:00 pm
Location: Atlanta, GA
Post
by burnt_toast » Mon May 12, 2008 9:38 am
nice lookin exhaust!
projects galore
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Mon May 12, 2008 12:22 pm
i like how it sticks out
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Mon May 12, 2008 7:09 pm
so i welded it up today. i started it up let her warm up for like 5min then i got on her and now she buries the speedo. it only did 25mph befor not it is doing over 35
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Mon May 12, 2008 7:22 pm
so i took the trans cover off today to check out the clutch and s***, i had to order a new gasket for it, and I'm going to change the gear oil. i am going to up jet it now, change the oil to Bel ray Si-7 synthetic, then do some plug chops.
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express
darat
Veteran OG
Posts: 3133 Joined: Fri Jul 23, 2004 10:24 am
Location: Fraser Michigan
Contact:
Post
by darat » Tue May 13, 2008 6:26 am
ya the mid range and top end changed big time. it pulls pretty good with that pipe on there.
MICHIGAN MOPED MAFIA Co Founder VET OG. 95 YAMAHA JOG 70CC
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Tue May 13, 2008 3:38 pm
i want to port the cylinder next, i found the thread about how to do it, but i still really don't get how to do it. I am ordering an extra Head off ebay to shave it down, dose any one know how much i should have shaved off??
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express
stillspeeding
Spree
Posts: 279 Joined: Fri May 04, 2007 3:50 am
Location: u.s.a
Post
by stillspeeding » Wed May 14, 2008 2:42 am
biturbo are useless, the "J" end from the exhaust is to smal, i ran them 25yrs ago and they sucked
Can't afford speed then stay away from it!
mopedman
CB900F
Posts: 1214 Joined: Mon Jul 23, 1973 10:24 am
Location: sterling Heights MI
Contact:
Post
by mopedman » Wed May 14, 2008 5:41 am
your useless, and i got 10 mph at least gain out of it
Michigan Moped Mafia founding member
2005 Yamaha Zuma
1985 Honda Spree
1978 Honda Express