polini for keli
Moderator: Moderator
polini for keli
my buddy has a polini overrange variator for the elite..i kno some mods need to be done no prob...but my ? is..should i trade him my keli for his polini??
1988 yamaha zuma
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: polini for keli
Greetings:
The Keli is a good $40 vario. The Polini sells sor a lot more, and is arguably a bit better.
If you're happy with tge Keli, and it's all tuned in, the hassle factor of fine-tuning the Polini should be considered in your decision.
The Polini "for Ruckus" needs case surgery to install, but is probably about the best you can get.
The Keli is a good $40 vario. The Polini sells sor a lot more, and is arguably a bit better.
If you're happy with tge Keli, and it's all tuned in, the hassle factor of fine-tuning the Polini should be considered in your decision.
The Polini "for Ruckus" needs case surgery to install, but is probably about the best you can get.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
- fastplastic
- CB900F
- Posts: 1161
- Joined: Tue May 11, 2010 7:37 pm
- Location: Manistee, MI
Re: polini for keli
doesn't take much to cut the case me and traffic jamz used a sawsall and made quick work of the carving process about 5 minutes then polish up with a dremal and your good to go!
-
- CBR1000RR
- Posts: 4219
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: polini for keli
The Polini for elite 50 requires no cutting. It is a better variator than the Keli IMO. If the Polini is in good condition, I would do it. Does it come with everything in the overange kit?
motormike wrote:Errands become adventures.
Re: polini for keli
I'm pretty sure this needs a lil cutting,, soo i can put the polini and not have to worry about the rear clutch or belt?
1988 yamaha zuma
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
Re: polini for keli
Also it's just the vari not the whole overrange kit
1988 yamaha zuma
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
-
- CBR1000RR
- Posts: 4219
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: polini for keli
Correct, when swapping in the Polini for Elite 50, the only thing you need to change from your stock setup are the roller weights.StrokedSr wrote:I'm pretty sure this needs a lil cutting,, soo i can put the polini and not have to worry about the rear clutch or belt?
If the case needs cutting, you do not have the Polini for Elite 50.
motormike wrote:Errands become adventures.
Re: polini for keli
So if it's not for the elite
N I have to cut.. Am I gunna need a longer belt!?
N I have to cut.. Am I gunna need a longer belt!?
1988 yamaha zuma
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
polini evolution kit
polini evolution 2 exhaust
polini big reed manifold
dellorto 21mm
keli clutch
keli variator
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: polini for keli
Greetings:
The only time you need a longer belt (and it's also wider) is if you change the REAR pulley. ZX spec is 654 x 18 x 30.
The only time you need a longer belt (and it's also wider) is if you change the REAR pulley. ZX spec is 654 x 18 x 30.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
-
- CBR1000RR
- Posts: 4219
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: polini for keli
Or if you are working on a non-variated motorWheelman-111 wrote:Greetings:
The only time you need a longer belt (and it's also wider) is if you change the REAR pulley. ZX spec is 654 x 18 x 30.
motormike wrote:Errands become adventures.