How to brighten your old faded, chalky plastics
Moderator: Moderator
-
- CBR1000RR
- Posts: 4957
- Joined: Sun Apr 16, 2006 11:51 am
- Location: Southern Michigan
How to brighten your old faded, chalky plastics
Just discovered something I though i would pass along.
Found out today that a WD-40 soaked rag followed by a dry one a few minutes later works wonders on body panels, turn signal housings and pretty much anything plastic on the bike, shines up the seat too. My spree went from a 20 yard bike to a 20 foot bike.
Found out today that a WD-40 soaked rag followed by a dry one a few minutes later works wonders on body panels, turn signal housings and pretty much anything plastic on the bike, shines up the seat too. My spree went from a 20 yard bike to a 20 foot bike.
I am not a mechanic, nor do I play one on TV. Actually my advice is probably worth slightly less than what you pay to view it.
Re: How to brighten your old faded, chalky plastics
Thanks Kenny for the tip--thats what I like about this forum, folks helping each other, and sharing info!
Will try this tomorrow!
Will try this tomorrow!
87 Honda Spree
86 Honda Spree
86 Honda Spree
- scooterwerx
- Elite
- Posts: 894
- Joined: Tue Oct 07, 2008 11:43 pm
- Location: redlands, ca
Re: How to brighten your old faded, chalky plastics
haha watch out for dust though, WD40 is like a magnet! turns it brown...
Re: How to brighten your old faded, chalky plastics
oooooooh yay gotta give this a try
1984 Honda Aero 50
1986 Honda Spree
1986 Honda Spree
- bradthreee
- Board Supporter
- Posts: 2142
- Joined: Tue Sep 12, 2006 4:20 pm
- Location: MARS...
Re: How to brighten your old faded, chalky plastics
I used Engine Brite engine degreaser on mine with a sponge, followed with a steady stream of water to remove the degreaser. Then sprayed Son of a Gun protectant in the yellow bottle as it was still wet. Let it soak for about 5 min not letting it dry then wipe off with a clean cloth. This did wonders for the plastics on my Gyro.
- burnt_toast
- Veteran OG
- Posts: 3592
- Joined: Sat Jul 31, 2004 8:00 pm
- Location: Atlanta, GA
Re: How to brighten your old faded, chalky plastics
Only thing I would think is this trick is likely temporary, similar to polishing. eventually would fade back
But a good one, especially if you have plenty wd40 handy
But a good one, especially if you have plenty wd40 handy
projects galore
Re: How to brighten your old faded, chalky plastics
I wet sanded my plastics to remove the surface oxidation. That way I don't have to redo it after the WD40 wears off.
-
- CBR1000RR
- Posts: 4957
- Joined: Sun Apr 16, 2006 11:51 am
- Location: Southern Michigan
Re: How to brighten your old faded, chalky plastics
The thing is dust doesn't stick to it any worse than it used to and it doesn't fell greasy. i would think that engine degreaser would dissolve plastic.
I am not a mechanic, nor do I play one on TV. Actually my advice is probably worth slightly less than what you pay to view it.
-
- Spree
- Posts: 162
- Joined: Sun Jul 20, 2008 4:24 am
- Location: Beautiful and Sunny>>Honolulu, Hawaii
Re: How to brighten your old faded, chalky plastics
Woot!
Last edited by TURN1 on Thu Jun 04, 2009 6:49 pm, edited 1 time in total.
Pass on the ALOHA Spirit!!!
- bradthreee
- Board Supporter
- Posts: 2142
- Joined: Tue Sep 12, 2006 4:20 pm
- Location: MARS...
Re: How to brighten your old faded, chalky plastics
Others may, but the "Engine Brite" made by Gunk is made for all under engine plastics as well. Its the best stuff I have ever used. I wouldnt tell people to use it if it would dissolve the plasticsKenny_McCormic wrote: i would think that engine degreaser would dissolve plastic.
-
- CBR1000RR
- Posts: 4957
- Joined: Sun Apr 16, 2006 11:51 am
- Location: Southern Michigan
Re: How to brighten your old faded, chalky plastics
Another thing I discovered, boil a carb in water to remove varnish. Do it outside in a junk pan(or go ghetto and use a dented to * dog food bowl)on a burner nobody cares about. Its not as good as buying a bucket of dip but it works.
I am not a mechanic, nor do I play one on TV. Actually my advice is probably worth slightly less than what you pay to view it.
Re: How to brighten your old faded, chalky plastics
What about Armorall? I think I can find a bottle in my son's stuff that he left for Pop to inherit when he left home. It's mine now.
Friends don't let friends buy Chinese bikes
Re: How to brighten your old faded, chalky plastics
I have read in more than one source that Armor All is bad for plastic. It eventually damages the plastic.Lunytune wrote:What about Armorall? I think I can find a bottle in my son's stuff that he left for Pop to inherit when he left home. It's mine now.
I stick to my above mentioned process. It removes the chalkiness instead of hiding it.
-
- BMX
- Posts: 47
- Joined: Sun Apr 19, 2009 1:43 am
- Location: IL
- Contact:
Re: How to brighten your old faded, chalky plastics
Hey,
Mothers has a nice product called Back To Black that i have used on my Black Spree and on my Mustang's trim with great results too.
Mothers has a nice product called Back To Black that i have used on my Black Spree and on my Mustang's trim with great results too.
Re: How to brighten your old faded, chalky plastics
I lied The Colgate tooth paste works OK , But after seeing some other postd on cleaning ,I tried Mothers back to black ... What a difference
Day & night worked great and a lot less work .So use the colgate for brushing your teeth and Mothers Back To Black for cleaning your plastic .
Day & night worked great and a lot less work .So use the colgate for brushing your teeth and Mothers Back To Black for cleaning your plastic .
- Attachments
-
- Rub Rub Rub in one direction do not go in circles .
- 100_5789.jpg (148.32 KiB) Viewed 11450 times
Last edited by 66SIX on Mon Oct 04, 2010 8:05 pm, edited 1 time in total.