Fab Flash 7: Fabrizi 50mm Cylinder Kit (74.6MPH)
Moderator: Moderator
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
Mannnnn..who has the fabrizi kits for sale again?
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow
-
- CB900F
- Posts: 1485
- Joined: Wed Mar 18, 2015 11:49 am
- Location: usa
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
Keith has the single ring version for sale last I knew.
Try out the lower gears and you'll be doing 80 no problem. Check the gear fluid regularly before going these speeds. Things get wonky quick doing 70+. Really awesome to see these cylinders shining. Also break in has just begun finishing on your cylinder so more power every day.
Try out the lower gears and you'll be doing 80 no problem. Check the gear fluid regularly before going these speeds. Things get wonky quick doing 70+. Really awesome to see these cylinders shining. Also break in has just begun finishing on your cylinder so more power every day.
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
You are flying! Great to hear. Ride safe.Wheelman-111 wrote:Greetings:
A liberal slathering of oily residue across the outer flank of the Fabrizi pipe's chamber underscored the fact: 52/125 is still WAY rich. Dropped to 50 /122 and Zoom! Houston, we have Lift-Off! Front wheel skims the tarmac on the way to 74.6 MPH @ 11K. Peak Temp still only 374. Fabrizi Rocks!
Thinkin' of re-installing taller 7.57:1 gears?
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
Do you have the polini 26? My stock pilot is a 45 and it starts right up, but I didn't even check to see what the main was. do you know?
98 Elite
4 strokes are for cars
4 strokes are for cars
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
Greetings:
If I did check, I don't remember what the original main size was. 45 pilot may be small, maybe 50 too big, but every engine is different, even if composed of the same parts. Use my values as a starting point, but Believe your own CHT, tach, ears, and Butt Dyno.
If I did check, I don't remember what the original main size was. 45 pilot may be small, maybe 50 too big, but every engine is different, even if composed of the same parts. Use my values as a starting point, but Believe your own CHT, tach, ears, and Butt Dyno.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
Hey wheel, is yours single ring?
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
No CHT or Tach. Just butt dyno and ears.Wheelman-111 wrote:Greetings:
If I did check, I don't remember what the original main size was. 45 pilot may be small, maybe 50 too big, but every engine is different, even if composed of the same parts. Use my values as a starting point, but Believe your own CHT, tach, ears, and Butt Dyno.
98 Elite
4 strokes are for cars
4 strokes are for cars
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
Greetings:
No, 2 rings on the Fab piston.
E, do yourself a favor and hit up G or R for a Vapor computer. Great device!
No, 2 rings on the Fab piston.
E, do yourself a favor and hit up G or R for a Vapor computer. Great device!
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
I like that air box , what name brand is it ?
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (70.4 MPH)
Greetings:
Unable to trace a tranny oil drip; 1 drop per day. I decided to hunt down a 2-bearing cover and convert to pre-1998. Starting with new dowels, bearings and clutch shaft seal. The correct gasket may be important to keep the oil, kicked up by the gears themselves, feeding the ball bearings of the mainshafts and the plain bearing surfaces of the countershaft. Ouija-boarded the cover on some 320 paper for a true flat surface. I'll do the same on the crankcase when the parts arrive. Sticking with 7.97:1 for now. We will see if the early cover and its 2 ball bearings makes any difference.
Unable to trace a tranny oil drip; 1 drop per day. I decided to hunt down a 2-bearing cover and convert to pre-1998. Starting with new dowels, bearings and clutch shaft seal. The correct gasket may be important to keep the oil, kicked up by the gears themselves, feeding the ball bearings of the mainshafts and the plain bearing surfaces of the countershaft. Ouija-boarded the cover on some 320 paper for a true flat surface. I'll do the same on the crankcase when the parts arrive. Sticking with 7.97:1 for now. We will see if the early cover and its 2 ball bearings makes any difference.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Requiem: Fab Flash 7: Fabrizi 50mm Cylinder Kit (74.6MPH)
Greetings:
As posted in Dude! Swap in a Spree!!
Flash 7 is to be retired. Lest ye succumb to despair, please know this fantastic, reliable Powerhouse is going to a better home than mine; I expect the talented Forumista in question will have more tuning time and talent, and will crack the Holy Grail of 82 MPH on 82cc. More to come on the post-mortem, maybe video. (I'll try... Wheelman is the Anti-Geek.)
As posted in Dude! Swap in a Spree!!
Flash 7 is to be retired. Lest ye succumb to despair, please know this fantastic, reliable Powerhouse is going to a better home than mine; I expect the talented Forumista in question will have more tuning time and talent, and will crack the Holy Grail of 82 MPH on 82cc. More to come on the post-mortem, maybe video. (I'll try... Wheelman is the Anti-Geek.)
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
- Rip_City_Spree
- CB900F
- Posts: 1379
- Joined: Sun Jun 13, 2010 7:47 pm
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (74.6MPH)
1man is getting the motor.
01 Elite SR
polini corsa
Polini 26mm Carb
Naraku intake
Naraku sport variator
Currently 5g rollers
zx trans
Arrow
red contra with yellow clutch springs.
RIP CITY
RIP NO MERCY KERSEY
polini corsa
Polini 26mm Carb
Naraku intake
Naraku sport variator
Currently 5g rollers
zx trans
Arrow
red contra with yellow clutch springs.
RIP CITY
RIP NO MERCY KERSEY
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (74.6MPH)
Hi wheelman. Now with the reflex it's smooth sailing.
you did everything possible for flash.
now that flash is being castrated for a good cause. lol respectfully.
you can keep the oil pump. tie it open on full, put a 92 jet in stock carb. no premix required. Have Wheelperson keep an eye on temp. I don't see any issues. I've been driving one like that for years. gas and go.
you did everything possible for flash.
now that flash is being castrated for a good cause. lol respectfully.
you can keep the oil pump. tie it open on full, put a 92 jet in stock carb. no premix required. Have Wheelperson keep an eye on temp. I don't see any issues. I've been driving one like that for years. gas and go.
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (74.6MPH)
Greetings:
Everything but 82 MPH on 82cc. Oh had I more time to goof with it. Or a better tailwind.
Flash 8 already has a pump plug installed. I'll see to it that her tires are aired and her tank full.
Everything but 82 MPH on 82cc. Oh had I more time to goof with it. Or a better tailwind.
Flash 8 already has a pump plug installed. I'll see to it that her tires are aired and her tank full.
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Re: Fab Flash 7: Fabrizi 50mm Cylinder Kit (74.6MPH)
Sorry to just jump in here, but did you imply that you are running a corsa and arrow pipe with a stock carb and oil pump, with no pre-mix? For how long? I am going by your signature also......ped wrote:Hi wheelman. Now with the reflex it's smooth sailing.
you did everything possible for flash.
now that flash is being castrated for a good cause. lol respectfully.
you can keep the oil pump. tie it open on full, put a 92 jet in stock carb. no premix required. Have Wheelperson keep an eye on temp. I don't see any issues. I've been driving one like that for years. gas and go.
Honda Elite SR
Honda Elite-Dio ZX
Dio ZX Headlight/Disc Brake Mod: http://hondaspree.net/phpBB3/viewtopic.php?t=30861
Honda Elite-Dio ZX
Dio ZX Headlight/Disc Brake Mod: http://hondaspree.net/phpBB3/viewtopic.php?t=30861