Dd50 rotory kit
Moderator: Moderator
-
- Noob
- Posts: 16
- Joined: Fri Jun 26, 2015 1:38 am
- Location: Hawaii
Dd50 rotory kit
Is there any rotory kit available for dd50 motors? Are they any good? And where could I get them?
-
- Elite
- Posts: 316
- Joined: Sat Nov 17, 2012 8:18 pm
- Location: Sunny Surburbon Sparta Michigan
Re: Dd50 rotory kit
What is a rotary kit ? Mazda RX7 has a rotary engine. Disc brakes have rotors. Most large cities have rotary clubs.
Better to ask and gain knowledge than to remain silent and ignorant.
Better to ask and gain knowledge than to remain silent and ignorant.
1984 Aero 125 57 mph for sale.
Elite 150 64 mph for sale.
Elite 250 77 mph. for sale.
Red Honda Grom, modded to 250cc, 87 mph.
GSXR 1000 168 mph. My new favorite, scooters seems way too slow now.
Elite 150 64 mph for sale.
Elite 250 77 mph. for sale.
Red Honda Grom, modded to 250cc, 87 mph.
GSXR 1000 168 mph. My new favorite, scooters seems way too slow now.
Re: Dd50 rotory kit
Internal rotor kit from treatland.tv for Honda dio
https://www.treatland.tv/honda-DIO-HPI- ... -coil.htms
https://www.treatland.tv/honda-DIO-HPI- ... -coil.htms
RideRed
<(2)Gyro S><Helix><Sym Wolf>
"Live Large - Ride Small"
<(2)Gyro S><Helix><Sym Wolf>
"Live Large - Ride Small"
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
-
- Elite
- Posts: 316
- Joined: Sat Nov 17, 2012 8:18 pm
- Location: Sunny Surburbon Sparta Michigan
Re: Dd50 rotory kit
Ahh, now I see.
My dirt bike buddies used to call that a PVL stator kit. Reduce rotating mass, increase crankshaft acceleration speed.
On the automotive side, Smokey Yunick was a big promoter of reducing rotating mass, he had a pretty good handle on increasing performance, dont think he dabbled in the two stroke world though.
My dirt bike buddies used to call that a PVL stator kit. Reduce rotating mass, increase crankshaft acceleration speed.
On the automotive side, Smokey Yunick was a big promoter of reducing rotating mass, he had a pretty good handle on increasing performance, dont think he dabbled in the two stroke world though.
1984 Aero 125 57 mph for sale.
Elite 150 64 mph for sale.
Elite 250 77 mph. for sale.
Red Honda Grom, modded to 250cc, 87 mph.
GSXR 1000 168 mph. My new favorite, scooters seems way too slow now.
Elite 150 64 mph for sale.
Elite 250 77 mph. for sale.
Red Honda Grom, modded to 250cc, 87 mph.
GSXR 1000 168 mph. My new favorite, scooters seems way too slow now.
-
- Noob
- Posts: 16
- Joined: Fri Jun 26, 2015 1:38 am
- Location: Hawaii
Re: Dd50 rotory kit
Yeah I can get my hands on a taida. Any feedback from them from anyone? And do you need to mod a dd50 block for it to fit?graphite9 wrote:ive been down this road, the only kits that work are taida, daytona and koso. Koso and daytona kits, if you can get them are $550-700. Taida is $299 and I have a few coming in to test. Someone in hawaii is selling the MVT modofied to fit, but what he doesn't realize is it won't fit. People should install things personally before advertising they work.
Re: Dd50 rotory kit
If you shave the stator bell you will lose top end, if you use a billet PG front face you can still gain off the line and top end.
some people dream of speed, i own your dreams!
Re: Dd50 rotory kit
so the lighter mass helps with torque off the line and at higher rpms? Sign me up..
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
Re: Dd50 rotory kit
Interesting....pretty sure I saw someone post that it fit, personally have seen it and done it , the only real issue is using it for air cooled requires a SMC rex or rexy fan as the stock fan is too wide and will hit the shroud, the original bracket failed almost instantly , the new custom ones shouldn't be a problem, but you never know all things fail especially experimental onesgraphite9 wrote:ive been down this road, the only kits that work are taida, daytona and koso. Koso and daytona kits, if you can get them are $550-700. Taida is $299 and I have a few coming in to test. Someone in hawaii is selling the MVT modofied to fit, but what he doesn't realize is it won't fit. People should install things personally before advertising they work.
Remember,everyone is human,even if there stupid!
-
- CB900F
- Posts: 1485
- Joined: Wed Mar 18, 2015 11:49 am
- Location: usa
Re: Dd50 rotory kit
Zombie on kymco forum did the mvt many years ago on a sc10as. It absolutely does NOT fit with out fabricating a collar. Will NOT fit with out fabrication.
Re: Dd50 rotory kit
Keyway are to set timing, but not needed, we have had the "taida" version since last year July I think? It's not bad but there are issues some major some not
First is the timing on the mag is set advanced, idk why but the"trigger" point is about 3/8 to 1/2" forward of a stock mag.
Second is the reliability, some last 6 months most wont, some fail with in 5 miles, how many kits are here? I personally brought in 30 and sold all but 1 which I used for mock up.
Third the fan that ones with it will explode on initial use- don't bother trying
Forth no timing adjustment, can slot the bracket or the pickup or both, I even attempted to have brackets made to do this
First is the timing on the mag is set advanced, idk why but the"trigger" point is about 3/8 to 1/2" forward of a stock mag.
Second is the reliability, some last 6 months most wont, some fail with in 5 miles, how many kits are here? I personally brought in 30 and sold all but 1 which I used for mock up.
Third the fan that ones with it will explode on initial use- don't bother trying
Forth no timing adjustment, can slot the bracket or the pickup or both, I even attempted to have brackets made to do this
Remember,everyone is human,even if there stupid!
-
- CB900F
- Posts: 1485
- Joined: Wed Mar 18, 2015 11:49 am
- Location: usa
Re: Dd50 rotory kit
What do you mean by forward of stock trigger
Re: Dd50 rotory kit
Imagine the stock trigger bump on the mag being 3/8 to 1/2" longer at the beginning, that would advance the timing "X" amount of degrees and that's exactly what they did on taida kit1man8scoots wrote:What do you mean by forward of stock trigger
Remember,everyone is human,even if there stupid!
Re: Dd50 rotory kit
Remember,everyone is human,even if there stupid!
-
- CB900F
- Posts: 1485
- Joined: Wed Mar 18, 2015 11:49 am
- Location: usa
Re: Dd50 rotory kit
That's not adjustable? I'll have a taida here soon, it's nice to know the short comings before I install it on an engine I'm not going to run before it's shipped.