Some pics
Moderator: Moderator
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Finally done..
54mm /52.6/=121cc
- Attachments
-
- image.jpg (143.21 KiB) Viewed 12665 times
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow
Re: Finally done..
Sweet is it running yet? What manifold are you going to use?
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Re: Finally done..
Thanks, havent ran it yet..but manifold will be big black ct..or kitaco
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow
Re: Finally done..
I would port match either if I was you. The ct for sure, kitaco is a little better but still casting flaws. I bet you're ready for some riding.
Re: Finally done..
Funny enough, I'm about to start running one of my built yamaha blasters with a 32mm keihin on a trinity 240 big bore and Vito's racing +3mm stroked crank. I believe it comes out to 252cc.
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Re: Finally done..
Port match what? Yea man so ready to ride..wana see the difference from my ministroker
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow
Re: Finally done..
I should have said smooth the rough angles rather than port match. I had the right tool in mind just not area. Im definitely full of envy of the build! Did you sell the old engine?
Re: Finally done..
hi DSD. very nice work. like to see that running.
Life's a trip enjoy the ride.
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
94 elite SR, 86 spreedio, polini corsa, keli variator, 8.4, jet. speed 65 mph
spreedio video. https://www.youtube.com/watch?v=BZr46_-douQ
- Trafficjamz
- CBR1000RR
- Posts: 5353
- Joined: Tue Jul 14, 2009 7:53 pm
- Location: Eastlake, MI
- Contact:
Re: Finally done..
graphite9 wrote:The guy that has been supplying my pipes, has a manifold they use on 120cc dios. It looks like they actually cut the case and cram a bigger manifold in. Has anyone ever heard of that? I'm waiting on better pics. I also might grab a japanese 125cc dio race pipe called Chou chin bullpipe...Anyone seen one before? The pipe diameter is HUGE
I'll be following this build for my 125cc setup.
The bigger ct black requires that you mod the block a bit.
The front two manifold bolts go in from underneath.
More mods are needed to cram vforce reeds in there.
new best 1/8th mile time 9.647 seconds @67.155 mph 310lbs total weight
- Red Eft Performance
- Elite
- Posts: 449
- Joined: Sat Jun 11, 2011 10:40 am
- Location: maine
Re: Finally done..
Thats the bore and crank I run on my street bike. Im running Large scorp and it is crazy fast.
Did you check your port timings? The Port timings on mine were wack. I ended up machining Some off the bottom of the cylinder cause the port timings were way too high.
Keith
Did you check your port timings? The Port timings on mine were wack. I ended up machining Some off the bottom of the cylinder cause the port timings were way too high.
Keith
Red Eft Performance
To benefit forum members REP will beat the price of any legit/active Business/website
Elite, Dio, Aero, AF16/AF05 Cylinder kits,Clutches,Variators,Belts,CDI boxes,Reeds,Clutch bells,Pipes
Malossi,Polini,Fabrizi,Anything!
View products click => Here
To benefit forum members REP will beat the price of any legit/active Business/website
Elite, Dio, Aero, AF16/AF05 Cylinder kits,Clutches,Variators,Belts,CDI boxes,Reeds,Clutch bells,Pipes
Malossi,Polini,Fabrizi,Anything!
View products click => Here
Re: Finally done..
Vforce 3 reeds from a kx65 fit in the normal ct perfectly no mods at all. Im not sure about the ct black though. Now there are Vforce 4 out and I would get those instead. They are the same price but more flow. I thought there was some porting also involved with the black but didnt know for sure.
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Re: Finally done..
Wont let me post a picture of my pipe for some reason..but im using a scooter alley big scorpion..as for port timing and that i had a good fella help me out with that (tru) should be fun
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Some pics
Heres another
- Attachments
-
- image.jpg (172.87 KiB) Viewed 12546 times
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow
- Wheelman-111
- Moderator
- Posts: 11325
- Joined: Wed Oct 22, 2008 5:09 pm
- Location: Deepinnaharta, Texas
Re: Some pics
Greetings:
How do you fit cooling shrouds?
How do you fit cooling shrouds?
Wheelman-111
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
Most of my money is spent on scooterparts. The rest is just wasted.
"ISO": '03 Vespa ET4 Malossi187 74MPH
Flash 9: 2001 Elite SR Contesta 72 ZX Tran, 9:1 Gears, Stock Airbox/Carb/Pipe 58.8 MPH
Punkin: 2010 Vespa/Malossi S78, 61MPH
- Downsouthdio
- CB900F
- Posts: 1205
- Joined: Wed Dec 21, 2011 11:00 am
- Location: Key west
Re: Some pics
Gunna have to rig something up..the spark plug sits straight up and not at an angle back like most
Honda super dio
Corsa
26mm
Sparrow
Corsa
26mm
Sparrow